Publicité
Congratulations!
You have chosen to purchase a
high-quality product. Familiarise
yourself with the product before
using it for the first time.
Read the following
assembly instructions
and the safety information
carefully.
Use the product only as described
and only for the given areas of
application. Store these assembly
instructions carefully. When pass-
ing the product on to third parties,
please also hand over all accompa-
nying documents.
Read all safety instruc-
tions and directions. Failure
to comply can cause serious
injury.
Scope of delivery
(fig. A)
1 x pavilion tent, unassembled (1-8)
4 x tension rope (9)
8 x ground spike (10)
1 x pavilion roof (11)
1 x assembly instructions
Technical data
Dimensions:
approx. 295 x 295 x 250cm
(w x d x h)
Date of manufacture
(month/year): 11/2023
Intended use
The product is designed for outdoor
use as protection against the sun.
It is not intended for long-term use
outdoors since it is weatherproof
only to a limited extent.
The product is not intended for com-
mercial use.
Safety instructions
Danger to life!
• Never leave children unsupervised
with the packaging material. Risk
of suffocation.
8
GB/IE/NI
Risk of injury!
• The product may not be used in
adverse weather conditions such
as strong wind, rain, or snow.
• The pavilion tent must be disman-
tled when wind speeds of greater
than 40km/h are anticipated
(brisk wind, large branches and
trees are moving, and the wind is
clearly audible).
• Stand the product on a level
surface.
• The product may only be used
under adult supervision and not as
a toy.
• Check the product for damage
and wear before each use.
• Check that all parts have been
assembled properly before each
use. Incorrectly performed assem-
bly may compromise safety and
function.
• No open fire, grills (barbecues),
or patio heaters are permitted
in or close to the pavilion tent.
Should a pavilion tent catch fire
despite these precautions, get out
immediately! Use a fire extinguish-
er or water to put out the fire. Call
the fire brigade immediately if
necessary.
• Individual pavilions may not be
connected or attached to each
other. A minimum distance of 3m
must be kept between individual
pavilions.
• Any pockets of water that form
must be emptied.
Selecting the location
• The dimensions of the product are
approximately 3 x 3m.
• Place the product in a location as
protected from the wind as possi-
ble.
• The ground should be flat and
the ground spikes should provide
adequate stability.
Assembly
Parts list (fig. A)
1 - Roof pole
2 - Pole for corner connection
3 - Cross pole
4 - Leg pole, upper
5 - Leg pole, lower
6 - Corner connection
7 - Gable connection
8 - Base
9 - Tension rope
10 - Ground spike
11 - Pavilion roof
Note! At least 2 people are
needed to assemble the prod-
uct.
We recommend performing
the assembly with 4 people.
Step 1
Insert the roof poles (1) into the
gable connection (7) as shown in
fig. B.
Step 2
Insert the poles for the corner con-
nection (2) and the leg poles (4)
into the corner connection (6), as
shown in fig. C.
Step 3
Connect the corner structures and
the cross poles (3) to each other.
Place the gable structure onto the
base frame (fig. D).
Step 4
Pull the pavilion roof (11) over the
assembled frame of the roof (fig. E).
Use the hook-and-loop fasteners on
the pavilion roof to fasten it to the
roof frame.
Step 5
Insert the leg poles (5) and bas-
es (8) beneath the roof frame
(fig. F).
Step 6
Secure the product with four
ground spikes (10) and the tension
cords (11), which are attached to
the loops on the pavilion roof, and
with four more ground spikes on the
bases (8) (fig. G).
Warning! Make sure that the
ground spikes hold securely.
Publicité
