Publicité
Les langues disponibles
Les langues disponibles
Product overview
4
5
3
2
1
Desk clamp
3
Glass lens
5
On/off switch (hidden)
7
Arm (for adjusting the light)
Installation
Never place the product in the vicinity of flammable materials (e.g. curtains or decorative
material). This may cause a fire (e.g. when using the lamp while soldering). Keep the
product out of the reach of children. Children may knock the lamp over and sustain
injuries. Never cover the lamp when it is in use. Never place the lamp on an unstable
surface, otherwise it may fall over and cause injuries.
• Remove the magnifying lamp from the packaging and secure it to a level, sufficiently hard surface (e.g. a
suitably thick table top or window sill). Ensure that the surface attached to the desk clamp has parallel
edges. The desk clamp must not be attached to desks with chamfered or tapered edges.
• Use the arm (8) to adjust the lamp head to the desired position. You can fine tune the horizontal position
with the swan neck (7).
Operation
a) Connecting the power adapter
• The magnifying lamp is powered by the power adapter provided.
• Plug the low-voltage power-in plug on the power adapter into the power adapter socket (9) on the side
of the lamp.
• Plug the power adapter into a standard mains socket connected to the public grid.
b) Using the magnifying lamp
• Switch on the magnifying lamp with the on/off switch (5).
- Position "O": Lamp is switched off
- Position "I": Lamp is switched on
Avoid touching the lens with your fingernails or other sharp objects.
Care and cleaning
• Always disconnect the product from the power supply before cleaning it.
• Remove loose particles from the lens with clean compressed air, and then wipe off any remaining residue
with a soft lens brush.
• Clean the surface of the lens with a lens cloth or a soft, lint-free cloth. To remove fingerprints and other fat
residues, the cloth can be moistened with water or lens cleaning solution. Do not use rough or fluffy cloths.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these could damage the
housing or stop the product from functioning properly.
• Avoid excessive cleaning and applying too much pressure to the housing and lens.
6
1
2
LED light
4
Glass lens cover
6
Swan neck (for adjusting the magnifying glass)
8
Socket for power adapter
Disposal
This symbol must appear on any electrical and electronic equipment placed on the EU market.
7
This symbol indicates that this device should not be disposed of as unsorted municipal waste at
the end of its service life.
Owners of WEEE shall dispose of it separately from unsorted municipal waste. Spent batteries
and accumulators, which are not enclosed by the WEEE, as well as lamps that can be removed
from the WEEE in a non-destructive manner, must be removed by end users from the WEEE in
a non-destructive manner before it is handed over to a collection point.
Distributors of electrical and electronic equipment are legally obliged to provide free takeback of waste.
Conrad provides the following return options free of charge (more details on our website):
• in our Conrad offices
• at the Conrad collection points
• at the collection points of public waste management authorities or the collection points set up by
manufacturers or distributors within the meaning of the ElektroG
End users are responsible for deleting personal data from the WEEE to be disposed of. It should be noted
that different obligations about the return or recycling of WEEE may apply in countries outside of Germany.
Technical data
8
This product contains a light source of energy efficiency class G.
a) Magnifying lamp
Operating voltage ........................................ 21 V/DC
Protection class ........................................... III
LED quantity ................................................ 56
Clamp type .................................................. Table clamp
Dimmable .................................................... No
Lamp colour ................................................. White
Type of light source ..................................... SMD LED, 7 W
Light colour .................................................. 6500 K
Luminous flux per light source (lumen) ........ 600 lm
Lens material ............................................... Glass
Lens size ..................................................... Ø 127 mm
Refractive power .......................................... 3 dpt
Magnification factor ..................................... 1.75 x
Operating/storage conditions ....................... -10 to +40 °C, ≤95 % relative humidity (non-condensing)
Weight ......................................................... 2.52 kg
b) Power adapter
Input voltage / current .................................. 220–240 V/AC, 50/60 Hz
Output voltage/current ................................. 21 V/DC, 0.35 A
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or the capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2022 by Conrad Electronic SE.
2474889_v2_0522_02_dh_mh_en
Publicité
