cecotec BOLERO COOLMARKET COMBI 322 WD INOX D Manuel D'instructions page 34

ENGLISH
- After installing the refrigerator, wait 4 hours before using it to allow the refrigerant to
stabilise.
3. INSTALLATION
Place of installation
Ventilation condition
- The location you choose for the installation of the refrigerator must be properly ventilated
and away from heat sources. Do not place the refrigerator near heat sources, like a
cooker or pot, and avoid direct sunlight to ensure the cooling effect and save on energy
consumption. Do not place the refrigerator in a damp place, to avoid rust or loss of power.
The result of dividing the total space of the room in which the refrigerator is installed by
the amount of refrigerant load in the refrigerator must not be less than 8 g/m³.
- Note: The amount of refrigerant used by the refrigerator is specified on the rating plate.
Heat dissipation space
During operation, the refrigerator releases heat into the environment. Therefore, you should
leave at least 30 mm of free space at the top, more than 100 mm on both sides, and more than
50 mm at the rear of the refrigerator. Fig. 2
Width Depth (mm) Height A (mm)
(mm) (mm)
595 635 1855 966
Note:
figure 2 only illustrates the space required for the product.
Stable surface
Place the refrigerator on a solid, flat surface (the floor) to keep it stable, otherwise vibrations
and noises will occur. When the refrigerator is placed on a carpet, straw mat, polyvinyl chloride,
solid support plates should be placed under the refrigerator to avoid colour change due to heat
dissipation.
Preparing for use
Waiting time
Once the refrigerator is properly installed and cleaned, do not switch it on immediately. Be sure
to wait at least one hour before switching it on to ensure normal operation.
66 B O LE R O COOLM ARKET COM BI 3 2 2 WH ITE/INOX/ DAR K D
B O LE R O COOLM ARKET COM BI 3 2 2 WD INOX D
B O LE R O COOLM ARKET COM BI 3 2 2 GLASS WH ITE/BL ACK/GREY D
B (mm) C(°) E (mm) F (mm)
1202 130 50 100
Cleaning
Check the placement of the interior accessory parts and clean the inside with a soft cloth.
On
Connect the plug into a power socket to switch on the compressor. After one hour, open the
freezer door: if the temperature inside the freezer compartment has clearly dropped, the
cooling system is operating normally.
Food storage
After the refrigerator has been in operation for some time, the user may adjust its internal
temperature. Once the refrigerator has reached a suitable interior temperature, put in the food.
These will take 2 to 3 hours to cool down completely. In summer, when the temperature is high,
it may take more than 4 hours for food to cool down completely (try to open the refrigerator
door as rarely as possible).
If the refrigerator is installed in a wet place, be sure to check if the earthed cord and the
leakage breaker are working normally. If vibration noises occur due to contact of the
refrigerator with the wall or if the wall turns black due to air convection around the compressor,
remove the refrigerator from the wall. The installation of the refrigerator may cause noise
interference or image problems in mobile phones, landline phones, radio receivers, or
televisions near the device, so in this case, keep the refrigerator as far away from these objects
as possible.
Changing the opening direction of the door
If desired, you can change the direction in which the door opens, from the right side (by default)
to the left side.
Warning
- The refrigerator must not be connected to the power socket when you change the opening
direction of the door. Make sure to disconnect the plug from the power socket.
- Check figure 5 to check the tools you need.
- It is advisable to change the opening direction of the door between two people.
Fig. 5
A. Tools not supplied
7. 8-mm tube wrench
8. Flat-head screwdriver
9. Spatula
10. Crosshead screwdriver
11. Wrench
12. 8-mm wrench
B OLERO COO LMA RKET COMB I 322 W HITE/ IN OX/DA RK D
BOLERO COOLMARKET COMBI 322 WD IN OX D
BOL ERO CO OLMARKET CO MBI 322 GLAS S W HITE/B LACK/GREY D
ENGLISH
67