EINHELL 45.135.71 Mode D'emploi D'origine page 18

5. Before starting the equipment
Be sure to read the following information before
you put the cordless screwdriver into operation:
1. Charge the battery only with the charging unit
supplied.
2. Only ever use sharp drill bits and screwdriver
bits which are suitable for the purpose and in
faultless condition.
3. Always check for concealed electric cables
and gas and water pipes when drilling and
screwing in walls.
Additional handle (Fig. 1 /Item 13)
The additional handle (13) enables you to achieve
better stability whilst using the equipment.
The additional handle (13) is secured to the
housing by a clamp. It can be screwed to the right
or left side.
6. Operation
6.1 Charging the battery (Fig. 2-3)
1. Remove the battery pack (5) from the handle
(Fig. 2) by pressing the pushlock buttons (8)
on the left and right side of the battery pack
(5).
2. Check that your mains voltage is the same as
that marked on the rating plate. Plug the char-
ging cable (7) of the charging unit (6) into the
power socket. The green LED on the charging
unit then comes on.
3. Insert the battery pack (5) into the battery
charger (6). The red LED will come on to in-
dicate that the battery pack is being charged.
Charging has fi nished when the red LED
goes out and the green LED comes on again.
The battery pack may become a little warm
during the charging process. This is normal.
Caution! At temperatures of 45°C and higher the
battery cannot be charged. In this case remove
the battery from the charger, let it cool down and
then recharge it.
If the battery pack fails to charge, check for the
following:
•
Voltage at the power socket
•
Good contact at the charging contacts of the
charging unit
Anl_BT_CD_24_1_i_SPK1.indb 18 Anl_BT_CD_24_1_i_SPK1.indb 18
GB
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the power of the cordless equipment
drops. Never fully discharge the battery pack. This
will cause it to develop a defect!
6.2 Torque setting (Fig. 4 / Item 1)
The cordless hammer drill/screwdriver is fi tted
with a mechanical torque selector.
The torque for a particular screw size is set with
the setting ring (1). The torque is dependent on a
number of factors:
•
On the type and hardness of the material in-
volved
•
On the type and length of the screws used
•
On the requirements that the screw connec-
tion has to satisfy
The grating disengagement of the coupling in-
dicates that the selected torque level has been
reached.
Caution! Only ever adjust the setting ring
when the equipment is at a standstill.
6.3 Drilling/hammer drilling (Fig. 4)
•
For drilling purpose, adjust the torque setting
(1) to the setting "Drill".
•
For hammer drilling purpose, adjust the
torque setting (1) to the setting "Hammer".
In the drill and hammer drill settings the slip cou-
pling is non-functional. The maximum torque is
available for drilling and hammer drilling.
6.4 Changeover switch (Fig. 5/Item 3)
The slide switch above the On/Off switch is for
setting the direction of rotation of the cordless
screwdriver and for preventing the cordless
screwdriver from being switched on inadvertently.
You can select between clockwise and counter-
clockwise rotation. To avoid causing damage to
the gearing, the direction of rotation must only be
changed when the screwdriver is at a standstill.
When the slide switch is in the middle position,
the On/Off switch is blocked.
- 18 -
04.09.12 09:43 04.09.12 09:43