Publicité
Compliance Information
FCC Compliance Notice
Supplier's Declaration of Conformity
Product name: DJI RC 2
Model Number: RC331
Responsible Party: DJI Research LLC
Responsible Party Address: 435 Portage Ave, Palo Alto, CA 94306
Website: www.dji.com
We, DJI Research LLC, being the responsible party, declares that the above mentioned model
was tested to demonstrate complying with all applicable FCC rules and regulations.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
— Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End user must follow the specific operating instructions for satisfying RF exposure
compliance. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
The portable device is designed to meet the requirements for exposure to radio waves established by
the Federal Communications Commission (USA).
These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value
reported under this standard during product certification for use when properly worn on the body.
These requirements set a SAR limit of 4 W/kg averaged over ten gram of tissue. The highest SAR value
reported under this standard during product certification for use when properly worn on the limbs.
ISED Compliance Notice
CAN ICES-003 (B) / NMB-003 (B)
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the
following two conditions: (1) This device may not cause interference. (2)This device must accept
any interference, including interference that may cause undesired operation of the device.
L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux
CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :(1)L'appareil
ne doit pas produire de brouillage; (2)L'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
This equipment complies with RSS-102 radiation exposure limits set forth for an uncontrolled
environment. End user must follow the specific operating instructions for satisfying RF exposure
compliance. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter. The portable device is designed to meet the requirements for exposure
to radio waves established by the CNR-102.
Cet équipement est conforme aux limites d'exposition aux rayonnements RSS: 102 établies pour
un environnement non contrôlé. L'utilisateur final doit suivre les instructions spécifiques pour
satisfaire les normes. Cet émetteur ne doit pas être co-implanté ou fonctionner en conjonction
avec toute autre antenne ou transmetteur.
Le dispositif portatif est conçu pour répondre aux exigences d'exposition aux ondes radio
établie par le développement énergétique DURABLE.
These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest
SAR value reported under this standard during product certification for use when properly worn
on the body.
Ces exigences un SAR limite de 1,6 W/kg en moyenne pour un gramme de tissu. La valeur SAR la
plus élevée signalée en vertu de cette norme lors de la certification de produit à utiliser lorsqu'il
est correctement porté sur le corps.
These requirements set a SAR limit of 4W/kg averaged over ten grams of tissue. The highest SAR
value reported under this standard during product certification for use when properly worn on
the limbs.
Ces exigences un SAR limite de 4 W/kg en moyenne pour dix gramme de tissu. La valeur SAR la
plus élevée signalée en vertu de cette norme lors de la certification de produit à utiliser lorsqu'il
est correctement porté sur le membres.
The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems.
Les dispositifs fonctionnant dans la bande de 5 150 à 5 250 MHz sont réservés uniquement pour
une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes
de satellites mobiles utilisant les mêmes canaux.
View E-label
Swipe down from the top of the home screen to enter Quick Settings, tap
Compliance Info.
查看电子标签
从首页顶部下滑打开快捷面板，然后点击系统设置图标
CMIIT ID：2023AP4866
查看電子標籤
於首頁頂部向下滑動打開快捷面板，然後按下系統設定圖標
E 라벨 보기
홈 화면 상단에서 아래로 밀어서 '빠른 설정'을 실행하고
E ラベルの表示
ホーム画面の上部から下へスワイプし、クイック設定に入り、
情報 ] を選びます。
Voir le E-label
Balayez de haut en bas depuis l'écran d'accueil pour accéder aux Paramètres rapides, appuyez
sur
et sélectionnez Informations de conformité.
Visualizar selo eletrônico
Deslize para baixo a partir do topo da tela inicial para abrir as Configurações rápidas, toque em
e selecione Informações de conformidade.
部件名称
线路板
外壳
液晶屏（如有）
金属部件（铜合金）
内部线材
其他配件
本表格依据 SJ/T 11364 的规定编制。
○： 表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求以下。
×： 表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的限量要求。（产
品符合欧盟 ROHS 指令环保要求）
铅 (Pb)
汞 (Hg)
×
○
×
○
×
○
×
○
×
○
×
○
，选择认证信息。
，選擇認證資訊。
아이콘을 누르고 '준수 정보'를 선택하십시오 .
有害物质
六价铬
镉 (Cd)
+6
(Cr
)
○
○
○
○
○
○
○
○
○
○
○
○
をタップして、[ コンプライアンス
多溴联苯
多溴二苯醚
(PBB)
○
○
○
○
○
○
and select
(PBDE)
○
○
○
○
○
○
7
Publicité
