Publicité
Les langues disponibles
Les langues disponibles
GB
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
WARNING
Always wear eye protection
when operating or perfoming
maintenance on this tool.
WARNING
Air powered tools can vibrate
in use. Vibration, repetitive
motions or unfocomfortable po-
sitions may be harmful to your
hands and arms. Stop using
any tool is discomfort, tingling
feelingor pain occurs. Seek
medical advice before resum-
ing use
WARNING
Keep body stance balanced
and firm. Do not overreach
when operating this tool.
•
When wearing gloves and operating models with in side
trigger, always be sure that the gloves will not pre vent
the trigger from being released.
•
Wear safety shoes, hard hat, safety goggles, gloves,
dust mask and any other appropriate pro tec tive cloth-
ing while operating the tool.
•
Do not indulge in horseplay. Distraction can cause ac ci-
dents.
•
Keep hands and fingers away from the throt tle lever
until it is time to operate the tool.
•
Never rest the tool or chisel on your foot.
•
Never point the tool at anyone.
•
Compressed air is dangerous. Never point an air hose
at yourself or co–workers.
•
Never blow clothes free of dust with com pressed air.
•
Be sure all hose connections are tight. A loose hose not
only leaks but can come completely off the tool and while
whipping under pressure, can injure the operator and
others in the area. At tach safety cables to all hoses to
prevent injury in case a hose is accidentally broken.
•
Never disconnect a pressurised air hose. Al ways turn off
the air supply and bleed the tool be fore dis con nect ing
a hose.
•
Prevent exposure and breathing harmfull dust and
particles created when using this tool. Some dust cre-
ated by drilling are known to cause cancer, birth defects
or other reproductive harm e. g. cristoline silica from
bricks, cement and masonary products. To reduce your
exposure work in well ventilated conditions and use
approved safety equipment e. g. dust masks that are
designed to filter out microscopic particles.
16
WARNING LABEL IDENTIFICATION
WARNING
WARNING
Always wear hearing
protection when operating
this tool.
WARNING
Do not carry the tool by
the hose.
WARNING
103 psig
Operate at 103 psig
(7.0 bar/700kPa)
(7.0 bar/700 kPa Maximum
air pressure)
SPECIFIC WARNINGS
ON
OFF
•
The operator must keep limbs and body clear of the
chisel. If a chisel breaks, the tool with the bro ken chisel
projecting from the tool will sud den ly surge forward.
•
Do not ride the tool with one leg over the han dle. In ju ry
can result if the chisel breaks while riding the tool.
•
Know what is underneath the material being worked.
Be alert for hidden water, gas, sewer, tele phone or elec-
tric lines.
•
Use only proper cleaning solvents to clean parts. Use
only cleaning solvents which meet cur rent safety and
health standards. Use cleaning sol vents in a well-ven-
ti lat ed area.
•
Do not flush the tool or clean any parts with die sel fuel.
Diesel fuel residue will ignite in the tool when the tool
is operated, causing damage to in ter nal parts. When us-
ing models with outside triggers or throttle levers, take
care when set ting the tool down to prevent ac ci den tal
op er a tion.
•
Do not operate the tool with broken or dam aged
parts.
•
Never start the tool when it is lying on the ground.
•
This tool is not designed for working in ex plo sive at mo-
spheres.
•
This tool is not insulated against elec tric shock.
WARNING
Always turn off the air
supply and disconnect the air
supply hose before installing,
removing or adjusting any
accessory on this tool, or
before performing any
maintenance on this tool.
WARNING
Do not use damaged, frayed
or deterlorated air hoses
and fittings.
CAUTION
Always wear dust mask
when operating this tool.
Publicité
