HIKOKI G 12STX Mode D'emploi page 3

h) Keep handles and grasping surfaces dry, clean
and free from oil and grease.
Slippery handles and grasping surfaces do not
allow for safe handling and control of the tool in
unexpected situations.
5) Service
a) Have your power tool serviced by a qualifi ed repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
PRECAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach of
children and infi rm persons.
SAFETY WARNINGS COMMON FOR
GRINDING OR ABRASIVE CUTTING-
OFF OPERATIONS
a) This power tool is intended to function as a
grinder or cut-off tool. Read all safety warnings,
instructions, illustrations
provided with this power tool.
Failure to follow all instructions listed below may result in
electric shock, fi re and/or serious injury.
b) Operations such as sanding, wire brushing,
polishing or hole cutting are not to be performed
with this power tool.
Operations for which the power tool was not designed
may create a hazard and cause personal injury.
c) Do not convert this power tool to operate in a way
which is not specifi cally designed and specifi ed by
the tool manufacturer.
Such a conversion may result in a loss of control and
cause serious personal injury.
d) Do not use accessories which are not specifi cally
designed and specifi ed by the tool manufacturer.
Just because the accessory can be attached to your
power tool, it does not ensure safe operation.
e) The rated speed of the accessory must be at least equal
to the maximum speed marked on the power tool.
Accessories running faster than their rated speed can
break and fl y apart.
f) The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool.
Incorrectly sized accessories cannot be adequately
guarded or controlled.
g) The dimensions of the accessory mounting must
fi t the dimensions of the mounting hardware of the
power tool.
Accessories that do not match the mounting hardware of
the power tool will run out of balance, vibrate excessively
and may cause loss of control.
h) Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or cracked wires.
If power tool or accessory is dropped, inspect for
damage or install an undamaged accessory. After
inspecting and installing an accessory, position
yourself and bystanders away from the plane of
the rotating accessory and run the power tool at
maximum no-load speed for one minute.
Damaged accessories will normally break apart during
this test time.
i) Wear personal protective equipment. Depending on
j) Keep bystanders a safe distance away from work
k) Hold the power tool by insulated gripping surfaces
l) Position the cord clear of the spinning accessory.
and specifi cations
m) Never lay the power tool down until the accessory
n) Do not run the power tool while carrying it at your side.
o) Regularly clean the power tool's air vents.
p) Do not operate the power tool near fl ammable materials.
q) Do not use accessories that require liquid coolants.
Kickback is a sudden reaction to a pinched or snagged
rotating wheel, backing pad, brush or any other accessory.
Pinching or snagging causes rapid stalling of the rotating
accessory which in turn causes the uncontrolled power tool
to be forced in the direction opposite of the accessory's
rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched by
the workpiece, the edge of the wheel that is entering into the
pinch point can dig into the surface of the material causing
the wheel to climb out or kick out. The wheel may either jump
toward or away from the operator, depending on direction of
the wheel's movement at the point of pinching.
Abrasive wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking proper precautions as given below.
a) Maintain a fi rm grip with both hands on the power
3
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of
stopping small abrasive or workpiece fragments.
The eye protection must be capable of stopping fl ying
debris generated by various operations. The dust mask
or respirator must be capable of fi ltrating particles
generated by your operation. Prolonged exposure to
high intensity noise may cause hearing loss.
area. Anyone entering the work area must wear
personal protective equipment.
Fragments of workpiece or of a broken accessory may
fl y away and cause injury beyond immediate area of
operation.
only, when performing an operation where the
cutting accessory may contact hidden wiring or its
own cord.
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and could
give the operator an electric shock.
If you lose control, the cord may be cut or snagged and your
hand or arm may be pulled into the spinning accessory.
has come to a complete stop.
The spinning accessory may grab the surface and pull
the power tool out of your control.
Accidental contact with the spinning accessory could
snag your clothing, pulling the accessory into your body.
The motor's fan will draw the dust inside the housing and
excessive accumulation of powdered metal may cause
electrical hazards.
Sparks could ignite these materials.
Using water or other liquid coolants may result in
electrocution or shock.
KICKBACK AND RELATED
WARNINGS
tool and position your body and arm to allow you to
resist kickback forces. Always use auxiliary handle,
if provided, for maximum control over kickback or
torque reaction during start-up.
The operator can control torque reactions or kickback
forces, if proper precautions are taken.
English