Chapin Sk-1169-1 Mode D'emploi

WARNING
WARNING: Improper use or failure to follow instructions can result in explosive failure causing serious
eye or other injury. For safe use of this product you must read and follow all instructions. Do not leave a
pressurized sprayer in the hot sun. Heat can cause pressure build-up resulting in possible explosion. Do not
store or leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants and full foot
protection when spraying. Never use any tool to remove pump if there is pressure in sprayer. Never stand with
face or body over top of tank when pumping or loosening pump to prevent ejecting pump assembly and/or
solution from striking and injuring you. Never pressurize sprayer by any means other than the original pump.
Do not attempt to modify this sprayer. Replace parts only with manufacturer's original parts. This sprayer is
intended for Acetone only. Acetone is extremely flammable. This Acetone sprayer is intended for trained
professionals only. Not intended for the retail trade. Always read and follow chemical manufacturer's
instructions before use with this sprayer as some chemicals may be hazardous when used with this sprayer.
Parts, Piezas, Pièces
6-8136
Valve Seat Kit
Kit de la válvula
Ensemble de soupape
6-6093
Hose Black
Manguera para trabajos
pesados Negro
Tuyau pour service
6-1929
intense Noir
Nozzle & Brass Adapter
Tobera
Buse
301630-2
6-4608
Pump Assembly
Pressure Relief Valve
Asamblea de la
Válvula de descarga de
bomba
presión
Assemblée de pompe
Soupape de
décompression
6-8135
Dripless Shut-off
Cierre antigoteo
Arrêt anti-goutte
6-4604
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d'étanchéité (non inclus)
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Congratulations!
You have just purchased a quality Chapin product.
Register Your Sprayer Online @ www.chapinmfg.com Questions? Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
1. Hose to Tank
1A
Outlet
Tube
Outlet Tube
Adapter
1C
Discharge/ Assembly
• Make sure white outlet tube is attached to outlet tube adapter (Fig. 1A).
• Insert the outlet tube portion of the discharge assembly into the tank adapter (Fig. 1B).
• Proper placement of white outlet tube (Fig. 1C).
• Firmly insert the outlet tube adapter into the tank adapter (Fig. 1D) Lining up tab with notches on
Sk-1169-1
the tank adapter.
• Firmly tighten the retaining nut to the tank adapter (Fig. 1E).
2. Extension wand and Nozzle Assembly
Shut-off to wand to nozzle assembly
2A
Shut-off to nozzle assembly with included valve seat
2B
Metal Rod
To attach nozzle directly to shut-off, unthread brass extension nut and metal rod. Assemble
valve seat (included), nozzle adapter and nozzle to the shut-off as shown in figure 2C. Note
orientation of valve seat. It will leak if assembled incorrectly.
3. Pre-Use Check
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are
found, replace hose before using. Replace with original manufacturer's parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and
exterior of tank for signs of deterioration of body and bottom. Any sign of deterioration indicates
possible tank weakening and could result in explosive bursting under pressure. If any of these
signs are found, discard tank immediately and replace. Do not attempt to patch leaks, etc., as this
could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only
(Pump plunger 10-20 strokes and inspect for leaks).
5) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank,
and proceed with Filling, Pressurizing and Spraying Instructions.
7) Do: Inspect all metal parts including the wand, nozzle and fittings for rust, corrosion and pitting.
If any of these conditions are found, replace affected part with original manufacturer's part
before using.
011534-7 (A) R1020
1B
Outlet
Tube
Discharge
Assembly
No Outlet Tube
1D 1E
Gap Adapter
Tab/ Retaining Nut -
Tank Notch
Securely tightened.
Adapter
Nozzle
Metal Brass
Nozzle
Brass
Rod
Extension Adapter
Extension Nut
The dripless shut-off
comes assembled as
Metal Rod shown in figure 2A.
2C
Valve Seat
Nozzle
Nozzle Adapter
4. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: over fill to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and
tighten securely.
5. Pressurizing and Spraying
5A 5A 5B 5B 5C 5C
Do: Turn handle Do: Pump until you Do: Push handle, down, turn 1/4
clockwise to tighten. feel resistance. turn clockwise to lock. Begin
Push handle down, spraying. Re-pump sprayer as
turn 1/4 turn counter- required to maintain spray force.
clockwise to release.
6A 6A
6. Lock Off
For safety lock-off feature (no-spraying),
push trigger forward and rotate locking
mechanism into lock-off position(Fig. 6A).
Lock
7. To Release Pressure
1) Your sprayer is equipped with a pressure
7A 7A
relief/release valve (Fig. 7A). To release
pressure lift and hold the cap until air is
completely exhausted, or, turn the valve slowly
counter-clockwise until you hear air escaping
and wait air is completely exhausted (Fig. 7B).
2) Do: Stay away from the sprayer until all air
has escaped.
8. Wand Dock Clip
Choose the holder that fits your wand.
9. Care, Storage and Maintenance
1) Do: Follow chemical manufacture's instructions for cleaning. Rinse thoroughly with
recommended solvent. Follow Filling, Pressurizing and Spraying Instructions, except pump unit
only 8-10 strokes. Be sure that the wand and nozzle are thoroughly rinsed after each use.
2) Do: Open shut-off and allow recommended solvent to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening
in cover.
P.O. Box 549 700 Ellicott St.
Batavia, NY 14021-0549 U.S.A.
1-800-950-4458 www.chapinmfg.com
Trigger
7B 7B