Publicité
Les langues disponibles
Les langues disponibles
7 Basic operation
Note:
– Point the remote control at the control keypad (2) to operate.
– Before using the remote control for the first time, remove the protective foil from the
battery compartment.
7.1 Charging the product
Important:
Do not charge the product using the USB-A ports on a computer. The current supplied by
these ports may not be sufficient and can damage the computer.
Note:
The torch is not charged via the main rechargeable battery. The rechargeable battery of
the torch must be charged separately. See "Torch" for more information.
To charge the product:
1. Disconnect any connected mobile devices from the product.
2. Connect the USB Type-C
input (5) to a suitable USB power source (5 V/2.1 A) using the
®
supplied USB Type-A to USB Type-C
Charging starts automatically.
Æ
During the charging process, the LEDs below the
Æ
current charge level.
When the product is fully charged, all 4 LEDs under the
Æ
Note:
– A full charge takes approx. 10 hours.
7.2 Displaying the charge level
To display the charge level of the integrated rechargeable battery:
1. Press the
button on the control keypad (2).
OR
button on the remote control (3).
Press the
The LEDs below the
button indicate the charge level:
Æ
– 4 LEDs on: 100 %
– 3 LEDs on: 75 %
– 2 LEDs on: 50 %
– 1 LED on: 25 %
– 4 LEDs flashing: low battery
8 Fan
8.1 Operating the fan
1. Press the
button on the control keypad (2).
OR Press the
button on the remote control (3).
ON
The product will switch on.
Æ
The fan speed will be set to level 1 after you switch the product on.
Æ
2. Change fan speeds by repeatedly pressing the
On the remote control, repeatedly press the
button to decrease the fan speed.
3. To switch off the product, press the button
button on the remote control (3).
the fan stops. OR press the
OFF
8.2 Setting the timer
The timer function allows the fan to be switched off automatically after a preset time. To set
the timer:
1. Switch the fan on.
2. Press the
button on the control keypad (2).
The timer setting will change each time you press the button (1 hr → 2 hrs → 4 hrs →
Æ
8 hrs → Timer off).
OR Press the
,
,
or
8H
1H
2H
4H
The selected switch-off time will be set.
Æ
8.3 Configuring the swivel function
To configure the swivel function of the fan:
1. Switch the fan on.
2. Press the
button on the control keypad (2).
OR
Press the
button on the remote control (3).
The swivel setting will change each time you press the button (90° → 45° → swivel
Æ
function off).
cable.
®
button will flash and indicate the
button will light up.
button on the control keypad (2) OR
button to increase the fan speed or the
on the control keypad (2) repeatedly until
button on the remote control (3).
Note:
– In addition to the automatic swivel function, you can tilt the fan manually by up to 180°
in order to adjust the flow of air.
8.4 Filling the scent dispenser
The product has an integrated scent dispenser. To fill the scent dispenser:
1. Turn the scent dispenser capsule anti-clockwise to remove it from the back of the fan.
2. Pour the desired amount of a suitable fragrance (e.g. a room fragrance) on the sponge in
the capsule.
3. Reinsert the capsule and turn it clockwise to fix it in place.
9 Torch
9.1 Charging the torch
Note:
The torch is not charged via the main rechargeable battery. The rechargeable battery of
the torch must be charged separately.
1. Connect the supplied USB Type-A to micro USB cable to the micro USB port on the torch.
9.2 Switching the torch on/off
The torch (1) is held in its holder by a magnet and can be detached as needed. To switch the
torch on/off:
1. Press the button on the back of the torch.
The torch light will turn on.
Æ
2. Press the button to cycle through different light modes (Constant → Flashing → Wide
beam angle light → Light off).
3. (If using the wide beam angle light) Rotate the light body to adjust the light as desired.
4. Switch the torch off by repeatedly pressing the button until the light is off.
Important:
– When inserting the torch into the holder, make sure that the wrist strap is secure and
cannot get trapped in the fan blades.
Note:
– There is a micro USB port on the back of the torch. To recharge the torch, use the
supplied USB Type-A to micro USB cable to connect the torch to a suitable USB power
source.
10 Power bank
10.1 Charging mobile devices (power bank function)
Important:
– Make sure the connection specifications for your mobile device match the connection
specifications for the power bank (see "Technical data" section).
– Always read the operating instructions for the device you want to connect.
– Do not short circuit the USB inputs/outputs on the power bank.
To charge mobile devices:
1. First, disconnect the product from the power supply.
2. Connect the mobile device that you want to charge to the USB-A output (6). Use one of the
supplied cables or the charging cable included with your mobile device.
The charging process will start automatically.
Æ
3. Monitor the charging process. Once the mobile device is fully charged (or the built-in
battery of the product is empty), the charging process will stop.
4. To terminate the charging process manually, disconnect the cable connection between the
product and the mobile device.
Publicité
