Palram Vitoria 5000 Mode D'emploi page 3

113»
Care and Safety advice
IMPORTANT
Please read these instructions carefully before you start to assemble this Product.
Please
carry out the
steps in
the order
set
out
in
these instructions.
Keep these instructions
in
a
safe place
for future reference.
Please
follow the instructions
as
listed
in
this manual.
Sort the parts and check against the list of
contents.
For
safety purposes we strongly recommend that the product will
be
assembled
by at least
two
people.
Some parts have metal edges.
Please be
careful when handling components.
Always wear gloves, shoes and safety goggles during assembly.
Do
not attempt to assemble the carport
in
windy
or
wet conditions.
Dispose
of
all plastic bags safely
-
keep
them out of
reach
of
small children.
Keep
children away from the assembly
area.
Do
not attempt to
assemble the carport if you
are
tired,
have
taken drugs,
medications or alcohol, or if
you are prone to dizzy spells.
When using
a
stepladder
or
power tools, ensure that
you are
follow the
manufacturer's safety advice.
Do
not climb or stand on the roof.
Heavy
articles should not
be
leaned against the poles.
Please
consult your
local authorities if any permits
are
required to erect carport.
Keep
roof and gutters clean of
snow,
durt
& leaves.
Heavy
amounts of snow
on
roof
can
damage the carport making it
unsafe to
stand below or nearby.
This
product
was designed to
be used
mainly
as a
carport.
>>
Some versions
of this carport
are painted.
If
color
was
scratched during assembly it
can be
fixed with the following tints:
Gray
-
RAL
7012
»
Cleaning instructions
When
your carport
needs cleaning,
use
a
mild detergent solution and rinse
with
cold clean water.
Do not
use
acetone, abrasive cleaners, or others special detergents to clean the panel.
Before
Starting Assembly
This
carport must
be assembled on
a
solid base (such
as
concrete or asphalt).
Choose your
site
carefully before beginning assembly.
Site
surface (mainly below poles)
needs to
be level.
During assembly
use
a
soft platform below the parts to avoid
scratches and damages.
»T001
L
»
During Assembly
When
encountering the information
icon, please refer
to the relevant
assembly step for additional comments and assistance.
The
Vitoria carport
has 4
gutters
heads, you can choose
whether to
make
them active or keep them
in its
original condition
-
non active.
To
activate
please
follow
step
15
Step
1:
Carefully spread silicone glue along the cross-section of the profile #7573
and at once attach the profiles together. It
is
recommended to wipe the extra residue
silicone
Step
3:
It
is
recommended to
place
a
sheet
/
Carton below the parts
to
avoid
scratches and
peeling of paint.
Profile should be fixed in
front of the second
set
of
holes
from the
edge.
Step
5: Please
connect two parts when
one person lifts the construction
at
an
angle
as
illustrated
in
drawing
5a.
Step 9: Central channel should remain open.
Please place the panel aside
the central channel of the arched profile,
as
illustrated
in
the
top
circle.
Step
10: Do
not tighten the
screws fully,
until both
sides panels in place.
Step 11: Profile stretching occurs only when all screws closed fully,
at the same
time;
on
both
sides
Step 12: Repeat and
follow the
same action for
all
profiles left
as
explained
in
stages 10-11.
Step 15: Optional
-
if you wish to
use
the gutters
heads
for water drainage, pop the
inner plastic by making
a
small hole
with
a
screwdriver and.then pop it
with your
finger.
Step 17: Level the profiles legs and
then adapt screws and plugs
to the ground type.
»
General:
Tighten
all screws
at the end
of
assembly.
239 cm
/
94.11