Hilti NMX 6-22 Mode D'emploi page 8

Careful handling and use of batteries
▶
Comply with the following safety instructions for the safe handling and use of Li-ion batteries. Failure to comply can lead to skin
irritation, severe corrosive injury, chemical burns, fire and/or explosion.
▶
Use only batteries that are in perfect working order.
▶
Treat batteries with care in order to avoid damage and prevent leakage of fluids that are extremely harmful to health!
▶
Do not under any circumstances modify or tamper with batteries!
▶
Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C (176 °F).
▶
Never use or charge a battery that has suffered an impact or been damaged in any other way. Check your batteries regularly for signs of
damage.
▶
Never use recycled or repaired batteries.
▶
Never use the battery or a battery-operated power tool as a striking tool.
▶
Never expose batteries to the direct rays of the sun, elevated temperature, sparking, or open flame. This can lead to explosions.
▶
Do not touch the battery poles with your fingers, tools, jewelry, or other electrically conductive objects. This can damage the battery and
also cause material damage and personal injury.
▶
Keep batteries away from rain, moisture and liquids. Penetrating moisture can cause short circuits, electric shock, burns, fire and explosions.
▶
Use only chargers and power tools approved for the specific battery type. Read and follow the relevant operating instructions.
▶
Do not use or store the battery in explosive environments.
▶
If the battery is too hot to touch, it may be defective. Put the battery in a place where it is clearly visible and where there is no risk of fire,
at an adequate distance from flammable materials. Allow the battery to cool down. If it is still too hot to touch after an hour, the battery is
faulty. Consult Hilti Service or read the document entitled "Instructions on safety and use for Hilti Li-ion batteries".
Observe the special guidelines applicable to the transport, storage and use of lithium-ion batteries.
Read the instructions on safety and use of Hilti Li-ion batteries that you can access by scanning the QR code at the end of these
operating instructions.
Description
1
Product overview
Battery interface
@
Speed selector switch
;
Grips
=
Switch-on interlock
%
On/off switch
&
Chuck key
(
Intended use
The product described is a mixer. It is designed for mixing materials of low or high viscosity, depending on the mixing paddle used.
• For this product, use only Hilti Nuron lithium-ion batteries of the B 22 series. For optimum performance, Hilti recommends the batteries
stated in the table at the end of these operating instructions for this product.
• For these batteries, use only Hilti chargers of the type series stated in the table at the end of these operating instructions.
Items supplied
Mixer, mixing paddle, chuck key, operating instructions
Other system products approved for use with this product can be found at your local Hilti Store or at: www.hilti.group
Status indicators of the Li­ion battery
Hilti Nuron Li-ion batteries can indicate state of charge, fault messages and the battery's state of health.
Indicators for state of charge and fault messages
WARNING
Risk of injury by a falling battery!
▶
If the release button is pressed with a battery inserted in the product, subsequently check that the battery is correctly re-engaged and secure.
Short-press the release button of the battery to get whichever of the following status indications is applicable at the time.
State of charge and, if applicable, faults are indicated constantly as long as the connected product is switched on.
Status
Four (4) LEDs show constantly green
Three (3) LEDs show constantly green
Two (2) LEDs show constantly green
One (1) LED shows constantly green
One (1) LED slow-flashes green
One (1) LED quick-flashes green
4
Spindle locking switch
)
Key chuck
+
Release button, battery
§
Battery status indicator
/
Battery
:
Mixing paddle
∙
Meaning
State of charge: 100 % to 71 %
State of charge: 70 % to 51 %
State of charge: 50 % to 26 %
State of charge: 25 % to 10 %
State of charge: < 10 %
The Li-ion battery is completely discharged. Recharge the battery.
If the LED again starts quick-flashing after the battery has been
charged, consult Hilti Service.
2341693
7
*2341693*