Publicité
Les langues disponibles
Les langues disponibles
3. Check fit: When this device is well-fitted, your
voice should sound louder, deeper and hollow
when you talk.
WARNING! Rapid removal may damage the ear-
drum. For greater control and safety, remove
ear tip slowly with twisting motion to gradually
break the seal.
4. Remove earbuds slowly with a twisting motion to
gradually break the seal.
5. Wash ear tips with mild soap and warm water as
needed. Look for tears or cracks under any of the
silicone banded tip flanges/foam tips.
6. Replace if ear tips are damaged or no longer hold
ear tips firmly in place when worn, if ear tips are
damaged or if ear tips are not soft and pliable.
WARNING! Rapid removal may damage the ear-
drum. For greater control and safety, remove
ear tip slowly with twisting motion to gradually
break the seal.
If you cannot obtain a good fit, try a different size or
style ear tip.
Turning Earbuds ON/OFF
Once earbuds are removed from the case they au-
tomatically turn on. Pushing the left or right earbud
buttons for 3 seconds will turn the earbuds ON or
OFF. A tone will play and the LED on the earbuds
will show status of charge. See "Charging the battery
pack and Charging the earbuds" section for status
of charge. Removing the earbuds from the case or
turning the earbuds on will automatically put them in
Bluetooth
pairing mode. Turning the earbuds OFF
®
or placing them back in the case will disconnect
Bluetooth
. Placing the earbuds in the case turns
®
the earbuds OFF.
Auto-off mode-The earbuds will turn off after 30
minutes if earbuds are disconnected from Bluetooth
music is not playing, or jobsite aware mode is turned
off. Connecting to Bluetooth
mode on will reset the 30 minutes for auto-off mode.
Low battery- A tone will play 10 minutes before shut
down of the earbuds. Once battery is dead a tone
will play and shut off the earbuds.
Pairing with Bluetooth
• The first time the earbuds are removed from the
case, the earbuds will go into pairing mode.
• If no Bluetooth
device is connected, Bluetooth
®
pairing will begin automatically and the blue LED
earbud indicator light will flash on the earbud that
was first removed from the case.
• To manually pair after earbuds are OFF, press and
hold for 3 seconds on both earbud buttons to turn
ON. Continue holding for 5 seconds to connect to
a device. A 3-chime tone will sound when earbuds
activate pairing mode.
• The earbuds will continue to search for a signal for
3 minutes.
• While the blue LED light is flashing, select
"REDLITHIUM USB™ Jobsite Earbuds" on the
Bluetooth
capable device.
®
• A tone will play in the earbuds to confirm the devices
are paired successfully.
• After first time use, the earbuds will attempt to pair
with the previous connected Bluetooth
• If connection is lost between the earbuds and the
Bluetooth
device, the earbuds will try to reconnect
®
automatically to the last connected device for up
to 3 minutes.
or turning jobsite aware
®
®
device.
®
• If no connection is made after 3 minutes, a discon-
nect tone plays and Bluetooth
• If Bluetooth
is off, push one of the earbud buttons
®
to turn on Bluetooth
General Operation
Left Earbud
Right Earbud
,
®
Music Controls
Push the right earbud button once to Play/Pause music.
• Next track-Push right earbud button twice to skip
to the next track. Next track tone will play then
next track.
• Previous Track-Push right earbud button three
times to replay the track. Previous track tone will
®
play then previous track.
Volume
Use the paired Bluetooth
down the music volume. Recommended volume
for extended use is 85dBA or lower. Refer to your
Bluetooth
device manufacturer's instructions. To
®
reach the recommended volume for extended use
turn volume to 60% or lower.
6
is shut off.
®
.
®
Button
Function
Presses
Jobsite Aware
x1
Mode
Jobsite Aware
x2
Volume
x1
Play/Pause
x2
Skip
x3
Back
x1
Answer call
x1
Hang up call
x2
Reject call
device to turn up or
®
Publicité
