Publicité
13
Place the device in the cutout.
14
Secure the device to the mounting surface using the included screws
15
Install the decorative bezel by snapping it in place around the edges of the
device.
Mounting the Microphone Hanger
NOTICE
If you are mounting the bracket on fiberglass with screws, it is recommended
to use a countersink bit to drill a clearance counterbore through only the top
gel-coat layer. This will help to avoid cracking in the gel-coat layer when the
screws are tightened.
Stainless-steel screws may bind when screwed into fiberglass and
overtightened. It is recommended to apply an anti-seize lubricant on the
screws before installing them.
You can mount the microphone hanger in a convenient location near the radio.
1
Select a mounting location for the microphone within reach of the
microphone cable.
2
Using the microphone hanger
as a template, mark the pilot holes.
À
3
Drill the mounting holes using a 3 mm (
4
Secure the microphone hanger to the mounting surface using the included
screws
.
Á
Connection Considerations
Item Description
Notes
Ground
You can use the included grounding screw to connect the
À
connection
device chassis to water ground, if needed (Additional
Grounding Considerations, page 3).
Power, NMEA
You must connect the device to a 12 Vdc power source
®
Á
0183, and
(Connecting the Wiring Harness to Power, page 3).
speaker wiring
You can connect this device to a NMEA 0183 device using
harnesses
this wiring harness to share DSC and GPS information
(optional) (NMEA 0183 Device Connections, page 4).
You can connect this device to a hailer horn using this wiring
harness (optional) (Connecting to a Hailer Horn or PA
Speaker, page 4).
You can connect this device to an external speaker using this
wiring harness (optional) (Connecting to an External Speaker,
page 4).
Installation Instructions
.
Á
1
/
in.) drill bit.
8
Item Description
Notes
VHF antenna
You must connect the device to a VHF antenna (sold
Â
connection
separately) (Connecting a VHF Antenna, page 3).
Additional
You can add an additional microphone (sold separately) or
Ã
microphone
relocate the existing microphone on a A01654 AIS radio
connector
(microphone relocation kit sold separately).
This connector is not available on a A01653 radio.
NMEA 2000
You can connect this device to a NMEA 2000 network on your
®
Ä
connector
boat to share DSC and GPS information (optional) (NMEA
2000 Device Connections, page 3).
Connecting the Wiring Harness to Power
1
Route the wiring harness to the power source and to the device.
2
Connect the red wire to the positive (+) battery terminal, and connect the
black wire to the negative (-) battery terminal.
Additional Grounding Considerations
This device should not need any additional chassis grounding in most
installation situations. If interference is experienced, the grounding screw on
the housing can be used to connect the device to the water ground of the boat
to help avoid the interference.
Connecting a VHF Antenna
1
Mount the VHF antenna (sold separately) according to the installation
instructions provided with the antenna.
2
Connect the VHF antenna to the antenna port on the back of the radio.
NMEA 2000 Device Connections
NOTICE
If you are connecting this device to an existing NMEA 2000 network, the
NMEA 2000 network should already be connected to power. Do not connect
the NMEA 2000 power cable to an existing NMEA 2000 network, because only
one power source should be connected to a NMEA 2000 network.
If you are connecting this device to an existing NMEA 2000 network or engine
network by another manufacturer, you should install a NMEA 2000 Power
Isolator (010-11580-00) between the existing network and the Garmin devices.
If you are installing a NMEA 2000 power cable, you must connect it to the boat
ignition switch or through another in-line switch. NMEA 2000 devices will drain
your battery if the NMEA 2000 power cable is connected to the battery directly.
To connect this device to your existing NMEA 2000 network, you must
purchase a NMEA 2000 cable and connector.
If you are unfamiliar with NMEA 2000, you should read the "NMEA 2000
Network Fundamentals" chapter of the Technical Reference for NMEA 2000
Item
Description
Compatible NMEA 2000 chartplotter or other device
À
A01653/A01654 device
Á
Ignition or in-line switch
Â
NMEA 2000 power cable
Ã
NMEA 2000 drop cable
Ä
12 Vdc power source
Å
3
Publicité
