Télécharger Imprimer la page

Parts2o FP4840-01 Manuel D'instructions

Publicité

Liens rapides

Phone: 1-877-PUMP-P2O (877-786-7726)
Web Site: http://parts2o.com
Vertical Pump
Mounted Over Well
INSTRUCTIONS
Jet Packages FP4840-01 and FP4830-00
Single pipe installations require:
a.
Galvanized steel pipe.
b.
Leather packer type ejector with built-in foot valve.
c.
Special turned couplings to fit inside 2" (50mm) well
casing.
d.
Well casing adapter.
e.
Pipe holder.
1.
Place ejector in a pail of water for at least two hours to
soak leathers.
2.
After leathers are thoroughly soaked, connect ejector to
first length of pipe. Use pipe joint compound sparingly on
male threads.
3.
Use tripod and block and tackle to lower pipe into casing.
Use special turned couplings to reduce friction while low-
ering pipe. Use pipe joint compounds sparingly on male
threads.
NOTICE: Fill pipe with water as each length is added to be
sure foot valve and connections do not leak.
4.
Add lengths of pipe until jet reaches proper depth (your
well driller should supply this information).
Horizontal Pump
Pump
Gasket
Casing Adapter
Horizontal Casing Adapter
Flange
Suction Pipe
Well Casing
Single Pipe
Packer-Type Ejector
Strainer
1008 0993
2" Single Pipe Jet Kit
Suction Pipe
Suction Pipe
NOTE: As a guide, jet depths should be 10 to 20 feet
(3M - 6.1M) below lowest water level reached when pump is
running, if possible, but always at least 5 feet (1.5M) above the
bottom of the well. Pump must be OFF when working on jet.
5.
To properly seat leathers, after jet assembly is in position
move it up and down slightly. Water pressure in casing will
then seal leathers.
6.
With jet properly set, clamp pipe holder securely, remove
block and tackle and slide well casing adapter over top of
pipe. Reattach block and tackle, remove pipe holder, slide
well casing adapter into position and tighten to seal well
casing.
7.
Install nipples or steel-to-plastic adapters in casing adapt-
er. Install horizontal offset pipe as needed. Use pipe joint
compound (galvanized steel pipe) or teflon tape (plastic
pipe) on male pipe threads.
Pump
Union
Dresser Coupling
Drive Pipe
Well Casing
Single Pipe Packer-type Ejector
Strainer
238 1093
P2O-21 (10/02/13)

Publicité

loading

Sommaire des Matières pour Parts2o FP4840-01

  • Page 1 Strainer 1008 0993 INSTRUCTIONS 238 1093 Jet Packages FP4840-01 and FP4830-00 Single pipe installations require: NOTE: As a guide, jet depths should be 10 to 20 feet (3M - 6.1M) below lowest water level reached when pump is Galvanized steel pipe.
  • Page 2 2” 1008 0993 INSTRUCCIONES INSTRUCTIONS 238 1093 Paquetes de chorro FP4840-01 y FP4830-00 Trousses d’éjecteurs FP4840-01 et FP4830-00 Las instalaciones de tuberías simples requieren: Les installations à un seul tuyau requièrent : Tubo de acero galvanizado. Un tuyau en acier galvanisé.
  • Page 3 Jet Selection Instructions Instructions pour la sélection d’un injecteur Instrucciones para la seleccion del surtidor 1. Look in left-hand column to find 1. Chercher le numéro du modèle de 1. Observe la columna a mano pump Model Number. pompe dans la colonne de gauche. izquierda para buscar el número de modelo de la bomba.

Ce manuel est également adapté pour:

Fp4830-00