Berner BACRHD BL SDS Plus 18V Notice Originale page 21

TECHNICAL DATA
Code ...................................................................................................
Art. ......................................................................................................
Drilling capacity in concrete ................................................................
Drilling capacity in steel ......................................................................
Drilling capacity in wood .....................................................................
Light core cutter in bricks and limestone .............................................
No-load speed ....................................................................................
Rate of percussion under load ............................................................
Impact energy per stroke according to EPTA-Procedure 05/2009 .....
Chuck neck diameter ..........................................................................
Battery ................................................................................................
Battery voltage ...................................................................................
Weight according EPTA-Procedure 01/2014 (1.5/2.0 Ah) ..................
Weight according EPTA-Procedure 01/2014 (3.0/4.0/5.0 Ah) ............
Weight according EPTA-Procedure 01/2014 (8.0/9.0 Ah) ..................
Recommended ambient operating temperature .................................
Recommended battery types .............................................................
Recommended charger ......................................................................
Noise/Vibration Information
Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (K = 3 dB(A)) .................................................
Sound power level (K = 3 dB(A)) .....................................................
Wear ear protection!
Total vibration values (vector sum in the three axes) determined
according to EN 62841:
Hammer-drilling in concrete: vibration emission value a
Uncertainty K = ..................................................................................
Chiselling: vibration emission value a
Uncertainty K = ..................................................................................
WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in EN
62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration and noise emission may differ. This may significantly increase the
exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when it is
running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration and/or noise such as: maintain the tool and the
accessories, keep the hands warm, organization of work patterns.
WARNING
Read all safety warnings, instructions,
illustrations and specifications provided with this power tool.
Failure to follow all instructions listed below may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
HAMMER SAFETY WARNINGS
Safety instructions for all operations
Wear ear protectors. Exposure to noise can cause hearing loss.
Use auxiliary handle(s), if supplied with the tool. Loss of control
can cause personal injury.
Hold the power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may
contact hidden wiring.
Cutting accessory contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the operator an electric
shock.
Safety instructions when using long drill bits with rotary
hammer
Always start drilling at low speed and with the bit tip in contact
with the workpiece. At higher speeds, the bit is likely to bend if
allowed to rotate freely without contacting the workpiece, resulting
the personal injury.
Apply pressure only in direct line with the bit and do not apply
excessive pressure. Bits can bend causing breakage or loss of
control, resulting in personal injury.
482 138 - Berner-BACRHD BL18V.indd 21 482 138 - Berner-BACRHD BL18V.indd 21
CORDLESS ROTARY HAMMER
...................
h
...............................................
h
BACRHD BL SDS PLUS 18V
BACRHD BL SDS Plus 18V 01 00001- 99999
.......................250798
............................... 26 mm
............................... 13 mm
............................... 28 mm
............................... 65 mm
...........................1400 min
-1
........................0-4900 min
-1
.............................. 2,5 J
............................... 43 mm
.......................... Li-Ion
............................... 18 V
.............................. 3,2 kg
.............................. 3,5 kg
.............................. 3,9 kg
...................-18 ... +50 °C
.................BBP18V-X; BBPP 18V-X
BBC 14,4-18V; BBC-2 14,4-18V; BBCF 14,4V-18V
........................... 93,7 dB (A)
......................... 101,7 dB (A)
.............................. 8,9 m/s
2
.............................. 1,5 m/s
2
.............................. 9,5 m/s
2
.............................. 1,5 m/s
2
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use personal protective equipment. Always wear eye protection.
Protective equipment such as a dust mask, non-skid safety shoes, hard
hat or hearing protection used for appropriate conditions will reduce
personal injuries.
The dust produced when using this tool may be harmful to health.
Do not inhale the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g.
asbestos).
Switch the device off immediately if the insertion tool stalls! Do not
switch the device on again while the insertion tool is stalled, as
doing so could trigger a sudden recoil with a high reactive force.
Determine why the insertion tool stalled and rectify this, paying
heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool is sharp-edged and can become hot during use.
WARNING! Danger of cuts and burns
- when handling the insertion tools
- when setting the device down.
Wear protective gloves when handling insertion tools.
Chips and splinters must not be removed while the machine is
running.
When working in walls ceiling, or floor, take care to avoid electric
cables and gas or waterpipes.
21
ENGLISH
15.06.2023 10:41:22 15.06.2023 10:41:22