Publicité
a standard double pole switch that ensures complete
disconnection from the mains in category III overvoltage
conditions, in accordance with the installation rules. •
Warning! The power cable must be replaced by the
authorised technical support service or by a person with
similar qualifications.
● Please note! Before reconnecting the circuit to the
mains power supply, make sure that it is working correctly,
always check that the power cable is correctly installed.
Please note! Do not use with a programmer, timer,
separate remote control or any other device that activates
automatically.
RECOMMENDATIONS FOR USE
Recommendations for correct use in order to reduce the
impact on the environment: When cooking begins, the
device should be turned on at minimum speed, and left on
for a few minutes even after cooking is complete. Increase
the speed only if there is a large quantity of fumes and
steam, using the Booster function only in extreme cases.
To keep the odour reduction system running efficiently,
replace the carbon filter/s when necessary. To ensure the
high performance of the grease filter, clean it when
necessary. To improve efficiency and minimise noise, use
the maximum duct diameter indicated in this manual.
REGULATIONS
Equipment designed, tested and manufactured in
compliance with safety regulations: EN/IEC 60335-1; EN/
IEC 60335-2- 31, EN/IEC 62233. Performance: EN/IEC
61591; ISO 5167-1; ISO 5167-3; ISO 5168; EN/IEC 60704-
1; EN/IEC 60704-2-13;EN/IEC 60704-3; ISO 3741; EN
50564; IEC 62301. EMC: EN 55014-1; CISPR 14-1; EN
55014-2; CISPR 14-2; EN/IEC 61000-3-2; EN/IEC 61000-
3-3.
2. USE
The extraction system can be used in the duct-out version
with external evacuation, or in the recirculating version with
filtering and internal recirculation.
●
Duct-Out Version:
Vapours are evacuated outside through an exhaust pipe
attached to the connecting flange.
CAUTION! If the product features one or more carbon
filters, they must be removed.
Connect the product to wall-mounted exhaust pipes and
holes with a diameter equivalent to the air outlet
(connecting flange).
The use of pipes and outlet holes in the wall with a smaller
diameter will reduce the extraction performance and
drastically increase the noise level.
All responsibility in this regard is therefore denied.
• Use a ducting pipe with the shortest length necessary.
• Use a ducting pipe with the least number of bends
possible (maximum bend angle: 90°).
• Avoid drastic changes in the ducting pipe diameter.
●
Recirculating Version:
The suctioned air will be degreased and deodorised before
it is sent back into the room. To use the product in this
version, it is necessary to install an additional activated
carbon filter system.
ASSEMBLY BEFORE INSTALLATION
• Check that the product is the right size for the installation
area.
• Remove the activated carbon filter(s) if supplied (see also
relevant paragraph).
• It(they) must be reinstalled if the product is used in the
filter version.
• If there are panels and/or walls and/or wall units on the
sides, make sure that there is enough space to install the
product and that it is always possible to access the control
panel easily.
• Do not make any modifications to the device or its
mounting bracket on the wall!
• Ask a professional to fix the hood to the wall.
• The wall on which the hood will be fixed must be in good
condition and must not show any damage (cracks,
subsidence, humidity, etc.). It must also be strong enough
to support the weight of the hood.
• Do not drill a hole close to old holes, even filled ones.
• It is essential to consult a building professional to use the
anchoring system (screws, dowels, etc.) appropriate to the
material that makes up your wall, as well as to the weight of
the appliance. Respect the diameter of the fixing screws
indicated in this manual.
Note: The fixing screws and dowels supplied with the
product can only be used if they are suitable for your wall
type. If the screws and dowels provided are not suitable for
the type of your wall, it is essential to use an appropriate
system recommended by the professional installer.
• The holes intended for fixing the appliance or its mounting
bracket to the wall must not be modified.
• The wall must be drilled using a drill of the correct size for
the anchoring system.
• Regularly check the fixing points of the appliance on the
wall. Tighten them if necessary.
3. OPERATION
A
A= ON/OFF light switch.
B= ON/OFF switch and select speed 1 (in case of little
steam and smoke).
B+C= Select speed 2 (in case of medium amount of
steam and smoke).
B+D= Select speed 3 (in case of a lot of steam and
smoke).
4
B
C
D
Publicité
