Télécharger Imprimer la page
MINN KOTA 1810253 Guide De Référence Rapide
MINN KOTA 1810253 Guide De Référence Rapide

MINN KOTA 1810253 Guide De Référence Rapide

Commutateur à pression sans fil

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Compatible with Raptor and Bluetooth
STOMP SWITCH
UP Stomp
Switch
Pairing
Button
Auto Down Button
Auto Up Button
Auto Up Button/ Pairing Button
Single press to AUTO retract the anchor.
For the Raptor anchor, press and hold to
continually retract. The Raptor will continue
to retract when the button is held until the
button is released. Top right used to pair the
Wireless Stomp Switch to a Talon or Raptor.
Auto Down Button/ Pairing Button
Double press to AUTO deploy the anchor.
For the Raptor anchor, single press and hold
to continually deploy. The Raptor will continue
to deploy when the button is held until it
reaches its full range of operation or until the
button is released. Top right used to pair the
Wireless Stomp Switch to a Talon or Raptor.
INSTALLING THE WIRELESS
STOMP SWITCH
Your new Wireless Stomp Switch comes complete
with all of the hardware you'll need to install it
directly to the deck of your boat. Please review the
parts list, mounting considerations and tools needed
for installation prior to getting started.
Installation Parts List
Item /
Part #
Description
Assembly
A
2992530
STOMP SWITCH ASSEMBLY UP
B
2992531
STOMP SWITCH ASSEMBLY DOWN
2
2383455
SCREW-#8 X 1.0" PPH TY AB
Mounting Considerations
Before mounting your Wireless Stomp Switch, please
give consideration to the following:
a. Examine your boat to ensure that you will not
drill into any obstructions and that the hardware
will be accessible for assembly.
b. Make sure the area under the mounting
location is flat, clear to drill holes and that the
installation hardware will not damage existing
components below the mounting surface. It may
be necessary to shim or modify the mounting
surface under the mounting location to create a
flat area for the Wireless Stomp Switch Pedestal
to be mounted.
c. Mount the Wireless Stomp Switch in an area
that has a clear line of communication with the
Talon(s)/Raptor(s) it is intended to control for
optimum performance.
The Wireless Stomp Switch Owner's
Manual is available at
minnkota.
johnsonoutdoors.com
includes information
on compatibility, safety considerations,
compliance, maintenance, parts and more.
minnkota.johnsonoutdoors.com
®
enabled Talon Systems only.
d. Mount the Wireless Stomp Switch in an area
where it will not become a tripping hazard.
Tools and Resources Required
DOWN Stomp
• Pencil or similar marking tool
Switch
• Drill
• #2 Phillips Driving Bit
Installation
a. Review the Mounting
Considerations to
determine an
acceptable mounting
location. Once a
location is selected,
take the Wireless
Stomp Switch
Assembly (Assembly
#A or B) and remove
the Pedestal from the
Base by squeezing
the Tab on the top
side of the Stomp Switch by the molded
logo and pulling the Stomp Switch and
Pedestal apart.
NOTICE:
the Wireless Stomp Switch and needs to be
removed for installation.
NOTICE:
be repeated for both Wireless Stomp Switch
Assemblies (Assembly #A and B).
b. The Pedestal has three Mounting Holes that
are used to secure it to the boat. The bottom
side of the Pedestal is smooth. The smooth side
should be placed down, towards the boat when
the Pedestal is installed. Position the Pedestal
at the selected location and mark the Mounting
Holes with a pencil or similar marking tool.
Mounting
Mounting
Holes
Holes
Marked
Marked
Location
Location
Qty.
c. Double check the
1
Mounting Location.
1
Take the Screws (Item
6
#2) and place one
each in the Mounting
Holes of the Pedestal.
Make sure the
Mounting Holes line
up with the Marked
Locations and then use
a Drill with #2 Phillips
Driving Bit to secure
the Pedestal to the
Deck of the Boat. Do not over-tighten.
d. Once the Pedestal
is installed, take the
Wireless Stomp Switch
and reattach it to the
Pedestal. Make sure
the Notch on the
Pedestal is aligned
and then click the Tab
in place so that the
Wireless Stomp Switch
is fully seated into the
Pedestal on the Deck
of the Boat.
e. Repeat this process for both Wireless Stomp
Switch Assemblies.
Serial Number: ___________________________________________________________________
WIRELESS STOMP SWITCH
Stomp
Stomp
Tab
Tab
Switch
Switch
Notch
Notch
Pedestal
Pedestal
The Pedestal comes attached to
This installation process should
Pedestal
Pedestal
Pedestal
Pedestal
(top)
(top)
(bottom)
(bottom)
Screws
Screws
Pedestal
Pedestal
Deck
Deck
of Boat
of Boat
Mounting Holes
Mounting Holes
Stomp
Stomp
Switch
Switch
Tab
Tab
Pedestal
Pedestal
Notch
Notch
Deck of Boat
Deck of Boat
QUICK REFERENCE GUIDE
PAIRING THE WIRELESS
STOMP SWITCH
NOTICE:
Raptor and Bluetooth
the latest available software before use.
The Wireless Stomp Switch can be paired to control
either a Bluetooth
®
enabled Talon or Raptor. Use the
top right portion of either the Up
Button to pair each Wireless Stomp Switch. Each
should be paired, so be sure to repeat the process for
both the UP and DOWN Stomp Switch.
Pairing to a Talon
a. Retract the anchor on
Up Button Down Button
the Talon by pressing
the Up
button on the
Talon Indicator Panel.
b. Once the Talon is fully
retracted, select a
Wireless Stomp Switch
to pair. Press and hold
the Pairing Button (
or
) on the Wireless
Stomp Switch for at least 5 seconds. It must be
the top right corner to initiate pairing. The three
red LED's under the button will begin to scroll
in a clockwise direction to indicate the switch
is in Pairing Mode.
c. Immediately press and hold the Up
and the Down
button simultaneously on
the Indicator Panel on the Talon. The Depth
Indication LEDs on the Indicator Panel of the
Talon will begin to scroll . Once the LEDs are
scrolling, release the buttons on the Indicator
Panel. The Talon and Wireless Stomp Switch
will go into Pairing Mode for 30 seconds. If a
signal with three fast beeps occurs, the Talon
and Wireless Stomp Switch have successfully
paired. If 30 seconds pass while in Pairing Mode
and they do not successfully pair, an error tone
will sound indicating that the pairing was not
successful, and the Wireless Stomp Switch will
not be able to control the Talon.
d. If the Pair is unsuccessful, repeat the process.
e. Repeat the complete pairing process for both
Wireless Stomp Switches.
Pairing to a Raptor
a. Select a Wireless Stomp
Up Button
Switch to pair. Press
and hold the Pairing
Button (
or
) on
the Wireless Stomp
Pair Button
Switch for at least 5
seconds. It must be
the top right corner to initiate pairing. The three
red LED's under the button will begin to scroll in
a clockwise direction to indicate the switch is in
Pairing Mode.
b. Immediately press the Pair button on the
Indicator Panel located on the Raptor Pump
Assembly. The PAIR/Maintenance LED will begin
to flash blue. The Raptor and Wireless Stomp
Switch will go into Pairing Mode for 30 seconds.
If a signal with three fast beeps from the Pump
Assembly occurs, the Raptor and Wireless Stomp
Switch have successfully paired. If 30 seconds pass
while in Pairing Mode and they do not successfully
pair, a chirp will sound from the Pump Assembly,
signaling that the Pairing has timed out.
c. If the Pair is unsuccessful, repeat the process.
d. Repeat the complete pairing process for both
Wireless Stomp Switches.
©2023 Johnson Outdoors Marine Electronics, Inc.
1810253
®
Talon require
Button or Down
Indicator Panel
button
Pair LED
Indicator
Panel

Publicité

loading

Sommaire des Matières pour MINN KOTA 1810253

  • Page 1 WIRELESS STOMP SWITCH QUICK REFERENCE GUIDE Compatible with Raptor and Bluetooth ® enabled Talon Systems only. 1810253 d. Mount the Wireless Stomp Switch in an area PAIRING THE WIRELESS where it will not become a tripping hazard. STOMP SWITCH STOMP SWITCH...
  • Page 2 COMMUTATEUR À PRESSION SANS FIL GUIDE DE RÉFÉRENCE RAPIDE Compatible avec les systèmes Talon et Raptor Bluetooth® uniquement. 1810253 Pour une performance optimale, montez le COUPLAGE DU COMMUTATEUR À commutateur à pression sans fil dans une zone COMMUTATEUR À PRESSION PRESSION SANS FIL permettant d’avoir une ligne de communication nette...