General Safety Warnings For The Tool - Jumbo ayce R6212B Traduction De La Notice Originale

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

GENERAL SAFETY WARNINGS FOR THE TOOL

1. The equipment must never be used in surroundings where an explosive
atmosphere exists. Never mix in solvents or substances containing solvent
that have flashpoints below 21 °C.
2. Do not let the cable touch any parts of your body. Only use the extension cable
approved for use in the working area.
3. The unit must only be started and stopped when it is inside a mixing vessel.
Ensure that the mixing vessel is placed on a solid, secure base.
4. Never reach into the mixing vessel with your hands or any other object during
the mixing process.
5. When working with the mixer, we recommend that you wear work, goggles
and ear protectors.
6. Wearing close-fitting clothes is mandatory.
7. Always allow for reaction torque.
8. Take the reaction torque into account. During operation always hold the
equipment firmly in both hands.
The tool must be used only for its prescribed purpose. Any use other than those
mentioned in this manual will be considered a case of misuse. The user and not the
manufacturer shall be liable for any damage or injury resulting from such cases of
misuse.
To use this tool properly, you must observe the safety regulations, the assembly
instructions and the operating instructions to be found in this manual. All persons
who use and service the machine have to be acquainted with this manual and must be
informed about its potential hazards. Children and frail people must not use this tool. It
is also imperative that you observe the accident prevention regulations in force in your
area.
The same applies for general rules of occupational health and safety.
The manufacturer shall not be liable for any changes made to the tool nor for any
damage resulting from such changes.
Even when the tool is used as prescribed it is not possible to eliminate all residual risk
factors. The following hazards may arise in connection with the tool's construction and
design:
• Damage to the lungs if an effective dust mask is not worn.
• Damage to hearing if effective hearing protection is not worn.
• Hand-arm vibration syndrome if its use is not adequately managed.
GENERAL SAFETY WARNINGS FOR THE TOOL
Read all safety warnings and instructions. Failure to follow the
!
warnings and instructions may result in electric shock, fire and/or
serious injury.
WARNING
SAVE ALL THE WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE.
The term "power tool" in the warnings refers to your mains operated (corded) power
tool or battery operated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well lit. Cluttered and dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
2. Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords increase the risk of electric
shock.
e) When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric
shock.
f) If operating a power tool in a damp location is unavoidable, use a residual
current device (RCD) protected supply. Use of an RCD reduces the risk of
electric shock.
58 | 59
GB

Publicité

Table des Matières
loading

Table des Matières