Publicité
Les langues disponibles
Les langues disponibles
right-handed users. If the belt hook is not desired at all, it can
be removed from the tool.
To move the belt hook, remove the screw
in place then reassemble on the opposite side. Be sure to
securely tighten the screw.
Worklight (Fig. A)
CAUTION: Do not stare into worklight. Serious eye
injury could result.
The worklight
7
is activated when the trigger is depressed,
and will remain on for a short time after the trigger is
released. If the trigger remains depressed, the worklight will
remain on.
nOTE: The worklight is for lighting the immediate work
surface and is not intended to be used as a flashlight.
Cutting (Fig. A)
WARNING: Cut Hazard. Wear gloves and eye
protection when handling and cutting wire mesh
cable tray. The edges are sharp and can cause serious
personal injury.
WARNING: This tool has no provision to lock the
trigger switch in the ON position and should never be
locked ON by any other means.
For accurate work, always secure the workpiece
before cutting.
1. Position the wire mesh cable tray so that the material
is between the stationary cutting die
cutting die
4
.
2. Align the wire mesh cable tray with cutting dies.
3. Depress trigger
until the workpiece is fully cut.
1
nOTE: For lighting the immediate work surface, the
worklight
is activated whenever the trigger switch is
7
depressed, and will automatically turn off 20 seconds
after the trigger switch is released. The worklight is not
intended to be used as a flashlight.
4. The unit will automatically shut off when the cutting dies
have reached the open position.
When cutting overhead, always confirm workpiece is secure
before cutting and be sure the excess wire mesh cable tray
that is cut is disposed of safely.
Reset/Lock‑Off Button
The reset/lock-off button
tool and also serves as a lock-off button.
Cutting
To select normal cutting operation, release the trigger switch
and depress the reset/lock-off button on the right side of
the tool.
lock‑off
The center position of the button locks the tool in the off
position. When changing the position of the reset/lock-off
button, be sure the trigger is released.
Reset/Return
To select reset, depress the reset/lock-off button on the left
side of the tool.
that holds it
10
3
and moveable
2
determines the direction of the
NOTICE: The wire mesh cable tray cutter could stall
during a cut either as a result of a depleted battery,
or as a result of cutting a material too hard or too large.
Should the unit stop during the cut for any reason, move the
reset/lock-off button
in reset position (left side) and pull
2
the trigger switch
to open the cutting dies and remove
1
the material.
NOTICE: Do not attempt to cut in the reset direction.
Damage to the tool could result.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your D
WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those
offered by D
WALT, have not been tested with this
e
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact D
(1‑800‑433‑9258) or visit our website: www.dewalt.com.
Repairs
The charger and battery pack are not serviceable. There are
no serviceable parts inside the charger or battery pack.
WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement, when applicable) should
be performed by a D
D
WALT authorized service center. Always use identical
e
replacement parts.
English
e
WALT call 1-800-4-D
WALT
e
e
WALT factory service center or a
e
WALT
9
Publicité
