Xylem Jabsco 60010-2 Serie Manuel D'installation page 2

REMOTE CONTROL SEARCHLIGHT − MODEL 60010-2 SERIES 255 SL
FEATURES
• Two High Output Sealed Beam Lamps
• Sleek Design
• Rugged Construction
• Full 360° Rotation
• Remote Control and 25 ft. Cable Included
• Tough Polyurethane Finish
Model Number
60010-2012
60010-2024
INSTALLATION INSTRUCTIONS
LIGHT MOUNTING
Select a location for the light which will allow clear beam projection for-
ward and as far aft as possible. Searchlight base should be mounted on
a level, flat surface. A mounting block between the searchlight base and
mounting surface can be used. The block should be contoured to fit the
deck so the searchlight base is level. See mounting template attached
for plug and cable required clearance.
1. Mount light with front of base towards the direction of most intended
use (front of circular base is marked "front") with gasket under light
base.
2. Feed wire through hole and secure light in place. NOTE: cable con-
nectors are provided for easy wiring connections.
Mounting hardware is provided:
• 4 1/4-20 x 2" (6.5mm x 50mm) bolts
• 4 lockwashers
• 4 flatwashers
OPTIONAL SECONDARY CONTROL MOUNTING
If an additional control station is desired use control kit numbers 43670-
0004 (12 volt) or 18753-0335 (24 volt). Mount secondary control in same
manner as main control. Mount station selector panel near the main con-
trol (flybridge or lower).
1. Cut a 2" x 1-3/8" (51mm x 35mm) opening for station selector panel
within a 1 foot radius of the control.
2. Route secondary control cable from station selector panel to second-
ary control location (cable acquired separately - see cable listing).
3. Insert station selector panel thru mounting hole and attach connec-
tors to mating connectors from control and search-light. The connec-
tor marked "flybridge" to go to flybridge control and the connector
marked "lower" to lower control. The connector to the nearest control
can be plugged directly into the control. See diagram.
4. Use bedding compound or sealant to waterproof station selector pan-
el mounting.
5. Secure panel with self-tapping screws provided.
Voltage Amps
12 Vdc 8
24 Vdc 4
SPECIFICATIONS
Voltage:
Elevation Angle (degrees):
Housing Material:
Candle Power:
Bulb type
SPOT/SPOT
SPOT/SPOT
CONTROL MOUNTING
Choose a location for the main control near the helm which will allow
convenient operation. Control may be mounted on vertical, horizontal,
or inclined panel.
1. Route powerleads (supplied by customer) from the voltage source to
control. NOTE: Wiring must be 16 gauge with a maximum run of 15
feet.
2. Crimp terminals (supplied) onto the power leads, NOTE: larger termi-
nal is crimped to positive lead, smaller terminal is crimped to negative
lead.
3. Insert wiring cable thru back of hole and plug into control.
4. Use bedding compound or sealant to waterproof control.
5. Secure control with self-tapping screws provided.
CIRCUIT PROTECTION
Two (2) automotive blade type fuses are included in the control. One
(10 amp) protects the bulb circuit, the other (3 amp) protects the motor
circuit. In the event that it should be necessary to replace a fuse simply
pull off the protective cover and slide the fuse out.
3 Amp
Fuse
CONTROLS (INCLUDED)
2
12 Vdc and 24 Vdc
Up: 30°, Down: 30°
Thermoset Plastic
200,000
Weight lb(kg) Standard Carton
11 (5)
11 (5)
43670-0003 12 V
60070-0000 24 V
1
1
10 Amp
Fuse