Hoover 36900657 Instructions De Service page 22

with new ones of the same type. Caution: do not touch the
light bulb with bare hands.
• Replacing LED lamps (Fig.6):
If the appliance version is with LED lamps, the intervention of
a specialised technician is necessary to replace them.
• Commands (Fig.9):
Button A = Switches the lights On/Off. The "filter alarm" can be
reset by pressing the button for a few seconds.
Button B = Switches the appliance on/Decreases the extrac-
tion rate of the motor. If the speed of the cooker hood is set
to 1, it switches off.
Automatic extraction function: With this function the
appliance automatically adjusts the motor's extraction rate
according to the quality of the air below thanks to the sensor
located under the cooker hood (Fig.8).
To activate this function, press the "B" button for a few secon-
ds. The letter "S" will appear on the display.
When the hood is switched on, before automatic suction is
enabled, you must wait a period of time depending on the
sensor's type of setting. When this is not yet active, the decimal
point on the display will flash.
When the function is active, the suction power of the motor
cannot be modified manually.
At the end of the motor's operating cycle, with the automatic
function active, if the hood does not re-start within 10 minutes
it will be permanently switched off.
This same situation occurs if the function is activated and the
motor does not start operating within 10 minutes.
Setting the sensor: According to the type of hob (gas or
electric) it is possible to increase the effectiveness of the sensor
by matching the cooker hood with the right hob.
To carry out this operation, press the "B" and "D" buttons
together for a few seconds with the motor off.
- To match the cooker hood with a gas hob, press the "B"
button. A "P" and a "0" will alternate on the display.
- To match the cooker hood with an electric hob, press the "D"
button. A "P" and a "1" will alternate on the display.
To complete the setting, press the "B+D" buttons for a few
seconds.
The appliance has already been set for an electric hob by the
manufacturer.
Intensive: This function allows you to temporarily increase
the motor's extraction rate for about 6 minutes. To activate the
function, press the "D" button after selecting extraction rate
level 3. After 6 minutes, the appliance will return to operate
at extraction rate level 3. During this function the letter "P"
will be displayed.
Timer: This function allows you to set the operating time of
the appliance to about 15 minutes, even if the speed is modi-
fied later, which then switches off at the end. To activate the
function press the "E" button; the decimal point on the display
will start to flash. The timer and the intensive function cannot
be activated at the same time. The timer does not interact with
the lights. To deactivate the function, set the extraction rate
level back to "0".
Carbon filter: Carbon filters are used to purify the air which
is released back into the room. The filters are not washable
or re-usable and must be replaced at least once every four
months. Saturation levels of carbon filters depend on the fre-
quency with which the appliance is used, the type of cooking
performed and how often the anti-grease filters are cleaned.
To activate the filter alarm function, press the "A+E" buttons
together.
- To activate the carbon filter alarm, press the "D" button. An
"A" and a "1"will alternate on the display.
- To deactivate the carbon filter alarm, press the "B" button.
An "A" and a "0" will alternate on the display.
To deactivate this function, press the "A+E" buttons together
with the motor off.
Button C = The display shows the extraction rate of the motor
and all the functions of the buttons mentioned above.
Button D = Increases the motor speed.
Enabling/disabling WiFi: The appliance can be controlled
remotely with external devices. To enable the function press
"D+E" buttons for 3 seconds. "0" will be displayed and the
"Read only" function is active. If "D+E" buttons are pressed for
6 seconds, the "write" function is activated and "1" is displayed.
If the WiFi module has to be Reset, press "D+E" for at least 10
seconds; "R" will be displayed.
Monitoring function: This function allows the appliance to
monitor the environment for an indefinite time. In case of
sudden variations in the status of the air or unexpected com-
bustions, the hood will send to the connected external devices
an alarm and a flashing "A" will be displayed. To activate the
function keep "E" pressed and three horizontal lines will be di-
splayed. A decimal point will flash until the sensor is stabilised.
Press any key to deactivate the function.
Deterrent function: This function simulates the presence of
people in the residence. The appliance will switch the lights
on and off with cyclic repetitions (lights on for 25 minutes and
lights off for 5 minutes). To activate the function press "D" for 5
seconds with the hood off. Two vertical lines will be displayed.
Press any key to deactivate the function.
Filter Alarm:
• Saturation of Anti-grease Filters:
This function is activated after the appliance has been running
for approximately 30 hours.
The letter "F" and the current extraction rate level will alternate
on the display. The anti-grease filters must be cleaned.
To reset the function, press the "A" button for a few seconds.
• Saturation of Carbon Filters:
This function is activated after the appliance has been running
for approximately 120 hours.
The letter "A" and the current extraction rate level will alternate
on the display. The carbon filters must be replaced.
To reset the function, press the "A" button for a few seconds.
CUSTOMER ASSISTANCE SERVICE
Before contacting the Technical Assistance Service.
If the product does not operate at all, we advise you to:
- Check that the plug has been inserted into the power socket
correctly.
If you cannot identify the cause of the operating anomaly:
switch off the appliance (do not subject it to rough treatment)
and contact the Assistance Service.
PRODUCT SERIAL NUMBER. Where can I find it?
It is important that you inform the Assistance Service of your
product code and its serial number (a 16-character code which
begins with the number 3); this can be found on the guarantee
certificate or on the data plate located inside the appliance.
This will help to avoid wasted journeys being made by techni-
cians, thereby (and most significantly) saving the correspon-
ding callout charges.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY
FOR EVENTUAL DAMAGES CAUSED BY BREACHING THE
ABOVE WARNINGS.
- 20 -