Tips For Operation; Cleaning And Maintenance - grossag KFW 500 Mode D'emploi

 The appliance can be used by persons with reduced physical, sen-
sory or mental capabilities or lack of experience or knowledge if they
have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
 The appliance cannot be used by children. Children should be su-
pervised to ensure that they do not play with the appliance and its
parts.
 Packaging material such as plastic bags keep out of reach of chil-
dren. Danger of suffocation!
 In case of misuse, wrong handling or incorrect repair no liability will
be taken for possible damages. Claims under guarantee are also
excluded in such cases.
 The appliance is intended for household use only and may only be
used indoors. It is intended for use in environments such as staff
kitchens of shops, offices, farms or other work environments, or to
be used by clients in hotels, motels, bed and breakfasts and other
residential environments.
 The appliance is not intended for commercial or industrial use.
 Repairs at the grinder attachment must be carried out by qualified
personal. Substantial dangers for the user can appear from inap-
propriate repairs.
 If in doubt about the interpretation of the contents of this instruction
manual, please contact your dealer or use the provided contact ad-
dress.
 In case the device is sold by the original owner or given to third par-
ty users, instructions for safe use of the device must be handed over
to them, and they must have understood the hazards involved,
through reading the instruction manual and in particular the safety
warnings contained in it, which should always accompany the de-
vice.
Installing the Grinder Attachment to the Stand Mixer
 Before first use clean all detachable parts carefully (see chapter "Cleaning").
 Always make sure stand mixer speed control is at OFF-position and the stand mixer is not plugged in.
 Loosen the locking knob (A) by turning it counter clockwise and remove the cover.
 Insert the assembled grinder attachment into the attachment hub (B) of the stand mixer. Slightly twist the
grinder attachment back and forth to ensure that the grinder shaft (C) seats properly into the square hub
socket. The pin (D) on grinder backside must fit into the notch (E) on the attachment hub.
 Tighten the locking knob by turning it clockwise until the attachment is completely secured to the stand
mixer.
 Place the food hopper (6) on top of the grinder tube (5).
To Assemble Grinder Attachment
 Insert the auger (4) into the grinder tube (5).
 Place first the cutting knife (3) and then the cutting disc over the square shank of the grinder worm.
Attention: Observe that the flat sides of the cutting blades face and are adjacent to the cutting
disc (picture 8)!
Observe that the notch at cutting disc must align with the pin in the grinder tube!
Make sure that the two plastic rings (9) in back of auger are securely in place.
 Place the locking ring (1) on grinder tube and turn by hand until secured but not tightened.

Tips for Operation

 Cut food into small strips or pieces. Meat should be cut into long narrow strips.
 Feed food into grinder tube using food pusher (7).
 Clean the grinder attachment thoroughly immediately after use.

Cleaning and maintenance

 Switch the appliance off and pull the plug from the socket. Remove the grinder by first loosening the
locking knob and then pull out the grinder attachment from stand mixer.
 Loosen the locking ring and disassemble the attachment into its parts.
 Clean all parts of the attachment in warm soapy water with a soft cloth or sponge and rinse them under
the tab.
Important: Never use scouring or abrasive cleaning agents or aggressive liquids.
 For ease of cleaning, all parts can be washed in the dishwasher. We recommend gently cleaning cutting
knife and cutting discs with warm running water. Regular washing in the dishwasher may blunt the blades.
 Cutting knife and cutting discs can be rubbed with a little cooking oil.
Subject to changes.
7 8