Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
The connector of the connection cable must be splash-
proof.
When running the connection line observe that it does not
interfere, is not squeezed, bended and the plug connection
does not get wet.
Wind off completely the cable when using a cable drum.
Regularly check the extension cables and replace them if
they are damaged.
Do not use any defective connection cables.
Do not set up any provisional electrical connections.
Never bypass protective devices or deactivate them.
Only hook up the machine by means of a fault-current
circuit breaker (30 mA).
The electrical connection or repairs to electrical parts of
the machine must be carried out by a certified electrician
or one of our customer service points.
Repairs to other parts of the machine must be carried out
by the manufacturer or one of his customer service
points.
Use only original spare parts. Accidents can arise for the
user through the use of other spare parts. The manufac-
turer is not liable for any damage or injury resulting from
such action.
A
A
Chucking the beater:
Screw the bar (2a) on the beater attachment (2b).
B
Screw the beater assembly (2) on the shaft (8). Secure the
C
beater using the spanners (9).
S
S
Check that the machine is completely and correctly as-
sembled.
Before each use, check
Connection cables for defects (cracks, cuts, etc.).
−
Do not use any defective cables.
there are no damages at the machine
−
(see "safe working")
that the beater is properly secured.
−
Mains connection
Compare the voltage given on the machine model plate
e.g. 230 V with the mains voltage and connect the ma-
chine to the relevant and properly earthed plug.
Connect the machine via a 30 mA fault current safety
switch.
Do not use any defective connection cables.
Use connecting or extension cables up to a length of 1.5 m
featuring a core cross section of at least 25 mm².
Main fuse: 10 A
12
s
s
e
m
b
l
y
s
s
e
m
b
l
y
t
a
r
t
-
u
p
t
a
r
t
-
u
p
Switching on
Do not use any device where the switch can not be
switched on and off. Damaged switches must be repaired
or replaced immediately by the customer service.
D
Switching on
Operate the trip switch (4) at first. Press the ON/OFF button
(3) on the handle.
Start the machine at the lowest rotational speed. In-
crease the rotational speed with the speed control dial (5) if
required.
Switching off
Release the ON/OFF handle button.
2- speed gear
F
The device is equipped with a 2-speed gear.
1.
speed: 0 - 620 rpm
2.
speed: 0 - 810 rpm
For the speed selection turn the switch (6) by 180°.
Only operate this switch at standstill.
Speed control
E
With this type, the motor's speed and thus the agitator per-
formance can be adjusted. You can continuously adjust the
speed with the speed control (5).
1. speed: 0 - 620 rpm
2. speed: 0 - 810 rpm
W
o
r
k
i
n
g
w
W
o
r
k
i
n
g
w
If persons who have blood circulation problems are too
often exposed to vibrations damages to the nervous system or
to blood vessels may occur.
You can reduce vibrations:
- by thick and warm working gloves,
- shorter working time (have longer breaks).
See a doctor if your fingers swell, you don't feel well or your
fingers become numb.
In any case, adhere to all safety notes (see "Safe
working").
Instruction for using the agitator
Only use beaters recommended by the manufacturer.
Pay attention the max Ø 140 mm - PROMIX 1600
The supplied mortar beater is suited for following materi-
als:
larger amounts of tenacious and glutinous compounds
-
to be mixed such as paints, varnish, translucent inks,
adhesives, paste, glue, knifing filler, plaster, flooring
plaster etc.
Always use this device with the extra handles fitted.
i
t
h
t
h
e
a
g
i
t
a
t
o
r
i
t
h
t
h
e
a
g
i
t
a
t
o
r
Publicité
Table des Matières
