Vimar ELVOX SLAVE EKKO ART 200D EAM6.N Manuel Pour Le Raccordement Et L'emploi page 8

EKKO ART
IMPORTANT SAFETY INSTRUCTIONS
FOR THE INSTALLATION
- ATTENTION -
FOR THE SAFETY OF THE PEOPLE IT IS IMPORTANT
TO FOLLOW ALL THE INSTRUCTIONS.
FOLLOW ALL INSTALLATION INSTRUCTIONS
1° - This handbook is exclusively addressed to the specialized
personnel who knows the constructive criteria and the
protection devices against the accidents for motorized gates,
doors and main doors (follow the standards and the laws in
force).
2° - The installer will have to issue to the final user a handbook in
accordance with the EN 12635.
3° - Before proceeding with the installation, the installer must
forecast the risks analysis of the final automatized closing
and the safety of the identified dangerous points (following
the standards EN 12453/EN 12445).
4° - The wiring harness of the different electric components
external to the operator (for example photoelectric cells,
flashlights etc.) must be carried out according to the EN
60204-1 and the modifications to it done in the point 5.2.2 of
the EN 12453.
5° - The possible assembly of a keyboard for the manual control
of the movement must be done by positioning the keyboard
so that the person operating it does not find himself in
a dangerous position; moreover, the risk of accidental
activation of the buttons must be reduced.
6° - Keep the automatism controls (push-button panel, remote
control etc.) out of the children way. The controls must be
placed at a minimum height of 1,5 m from the ground and
outside the range of the mobile parts.
7° - Before carrying out any installation, regulation or maintenance
operation of the system, take off the voltage by operating on
the special magnetothermic switch connected upstream it.
THE ELVOX COMPANY
RESPONSIBILITY for possible damages caused by the non
observance during the installation of the safety standards and of
the laws in force at present.
Directive 2002/96/EC (WEEE)
The crossed-out wheelie bin symbol marked on the product indicates that at the end of its useful life, the product must be handled separately from household refuse and must
therefore be assigned to a differentiated collection centre for electrical and electronic equipment or returned to the dealer upon purchase of a new, equivalent item of equipment.
The user is responsible for assigning the equipment, at the end of its life, to the appropriate collection facilities.
Suitable differentiated collection, for the purpose of subsequent recycling of decommissioned equipment and environmentally compatible treatment and disposal, helps prevent
potential negative effects on health and the environment and promotes the recycling of the materials of which the product is made. For further details regarding the collection
systems available, contact your local waste disposal service or the shop from which the equipment was purchased.
Risks connected to substances considered as dangerous (WEEE).
According to the WEEE Directive, substances since long usually used on electric and electronic appliances are considered dangerous for people and the environment.
The adequate differentiated collection for the subsequent dispatch of the appliance for the recycling, treatment and dismantling (compatible with the environment) help
to avoid possible negative effects on the environment and health and promote the recycling of material with which the product is compound.
6 6
DOES NOT ACCEPT ANY
KEEP THESE INSTRUCTIONS WITH CARE
1° - Install a thermal magnetic switch (omnipolar, with a minimum
contact opening of 3 mm) before the control board, in case
this is not provided with it. The switch shall be guaranteed
by a mark of compliance with international standards. Such
a device must be protected against accidental closing (e.g.
Installing it inside the control panel key locked container).
2° - As far as the cable section and the cable kind are concerned,
ELVOX suggests to use an H05RN-F cable, with a minimum
section of 1,5mm , and to follow, In any case, the IEC 364
2
standard and Installation regulations In force In your Country.
3° - Positioning of an eventual pair of photocells: The beam of the
photocells must be at an height not above the 70 cm from the
ground, and, should not be more than 20 cm away from the
axis of operation of the gate (Sliding track for sliding gate or
door, and the hinges for the swing gate). In accordance with
the point 7.2.1 of EN 12445 their correct functioning must be
checked once the whole installation has been completed.
4° - In order to comply with the limits defined by the EN 12453
norm, if the peak force is higher than the limit of 400 N set by
the norm, it is necessary to use an active obstacle detection
system on the whole height of the gate (up to a maximum of
2,5m) - The photocells in this case must be apply externally
between the colums and internally for all the race of the mobil
part every 60÷70 cm for all the height of the column of the
gate up to a maximum of 2,5 m (EN 12445 point 7.3.2.1).
example: column height 2,2 m => 6 copies of photocells - 3
internal and 3 external .
N.B.: The system must be grounded
Data described by this manual are only Indicative and ELVOX
reserves to modify them at any time. Install the system complying
with current standards and regulations.
EN