Publicité
6
Alertes
Les alertes suivantes apparaîtront sur la manette en cas d'erreur avant vol ou en vol. Surveillez toujours la présence
d'alertes sur la manette et effectuez les actions recommandées.
6.1
Erreurs avant vol
Avant de démarrer les moteurs, Solo effectue une série de vérifications automatiques pour s'assurer que le système
est prêt à voler.
6.1.1
Calibrage
Les erreurs suivantes indiquent qu'un contrôle avant vol est en cours : calibrage d'altitude, calibrage de Solo et
calibrage de boussole. Veuillez attendre que l'erreur soit corrigée avant de continuer.
PREARM SENSOR ERRORS
Altitude
Please wait
Quand le Solo n'est pas placé sur une surface plane, vous recevrez l'alerte suivante vous invitant à déplacer le
Solo sur une surface plane pour le décollage.
Compass
Please calibrate compass using
the 3DR Solo app
Level
Please calibrate level
using the 3DR Solo app
Quand le Solo nécessite un calibrage manuel, les alertes suivantes montrent les affichages pour le calibrage de la
boussole et du niveau. Référez-vous à la section 9.2 pour les instructions relatives au calibrage de la boussole et
du niveau.
Sensor
Please try and restart Solo
Control stick
En cas d'erreur de calibrage ou de capteur pendant le démarrage, redémarrez le Solo pour résoudre les alertes
Contact 3DR customer support
suivantes.
Unknown
All manuals and user guides at all-guides.com
ARMING ALERTS
Calibration
Please restart Solo
ARMING ALERTS
Calibrating
Please wait
Calibration
Please restart Solo
Calibrating
Altitude calibration
Please wait
System self-calibrates altitude after altitude disparity
Alert persists until:
System self-calibrates (sys then continues sensor check)
Timeout: after 1 minute (?) (results in "sensor error" screen)
calibrating
Calibrating
Please wait
Throttle
Figure 6.1.1.1: Manette - Alertes de calibrage en cours
Compass error
User asked to use Solo app to calibrate.
PREARM SENSOR ERRORS
This flight mode requires low
throttle before starting motors
Alert persists until:
User completes calibration using the app (sys then continues sensor check)
Powers off controller, or Solo
error
Calibrating
Controller auto-shutdown
Note: Artoo will not assume the same error is present on
Please wait
restart, and will run a fresh check when connected to Solo.
Altitude
calibrating
Please wait
Uneven
Level error
User is asked to use Solo app to calibrate
Move Solo to a level surface
Alert persists until:
User complete calibration using the app (sys then continues sensor check)
Powers off controller, or Solo
error
Controller auto-shutdown
Figure 6.1.1.2: Manette - Alerte de surface non plane
Throttle
Note: Artoo will not assume the same error is present on
restart, and will run a fresh check when connected to Solo.
This flight mode requires low
Compass
error
throttle before starting motors
Please calibrate compass using
the 3DR Solo app
Sensor error screen
Service
For sensor errors requiring user-initiated restart
Use 3DR Solo app to log a trouble
ticket with customer support
error
Uneven
Level
error
Move Solo to a level surface
Please calibrate level
using the 3DR Solo app
Control sticl error
Persists until:
Controller starts with stick values in range.
Figure 6.1.1.3: Manette - Alertes de recalibrage requis
error
Service
Sensor
error
Use 3DR Solo app to log a trouble
ticket with customer support
Please try and restart Solo
Battery unknown
Displayed if Artoo is powered on with a battery has an
ID resistor unknown to Artoo. (Not logged in current software version's index.)
HAPTIC: Strong feedback, 40 millisecond pulse
?
After Solo is disconnected, Artoo should display "waiting for Solo"
battery
Altitude calibration
System self-calibrates altitude after altitude disparity
Alert persists until:
System self-calibrates (sys then continues sensor check)
ARMING ALERTS
Timeout: after 1 minute (?) (results in "sensor error" screen)
error
Calibration
Altitude calibration
System self-calibrates altitude after altitude disparity
Please restart Solo
Alert persists until:
System self-calibrates (sys then continues sensor check)
Timeout: after 1 minute (?) (results in "sensor error" screen)
Solo
Altitude calibration
System self-calibrates altitude after altitude disparity
Alert persists until:
System self-calibrates (sys then continues sensor check)
Timeout: after 1 minute (?) (results in "sensor error" screen)
Calibrating
error
Compass error
User is asked to use Solo app to calibrate.
Please wait
Alert persists until:
User completes calibration using the app (system then continues sensor check)
User powers off controller, or Solo
compass
Controller auto-shutdown
Altitude calibration
Note: Artoo will not assume the same error is present on
System self-calibrates altitude after altitude disparity
restart, and will run a fresh check when connected to Solo.
Alert persists until:
System self-calibrates (sys then continues sensor check)
Timeout: after 1 minute (?) (results in "sensor error" screen)
Calibrating
Solo
Compass error
User asked to use Solo app to calibrate.
Please wait
Alert persists until:
User completes calibration using the app (sys then continues sensor check)
Powers off controller, or Solo
too high
Controller auto-shutdown
Compass error
User is asked to use Solo app to calibrate.
Note: Artoo will not assume the same error is present on
restart, and will run a fresh check when connected to Solo.
Alert persists until:
Altitude calibration
System self-calibrates altitude after altitude disparity
User completes calibration using the app (system then continues sensor check)
Alert persists until:
User powers off controller, or Solo
Throttle
compass
System self-calibrates (sys then continues sensor check)
Level error
Controller auto-shutdown
User is asked to use Solo app to calibrate
This flight mode requires low
Timeout: after 1 minute (?) (results in "sensor error" screen)
Note: Artoo will not assume the same error is present on
throttle before starting motors
Alert persists until:
restart, and will run a fresh check when connected to Solo.
User complete calibration using the app (sys then continues sensor check)
Powers off controller, or Solo
surface
Controller auto-shutdown
PREARM SENSOR ERRORS
Compass error
Note: Artoo will not assume the same error is present on
User asked to use Solo app to calibrate.
restart, and will run a fresh check when connected to Solo.
Alert persists until:
Compass error
User asked to use Solo app to calibrate.
User completes calibration using the app (sys then continues sensor check)
Powers off controller, or Solo
Alert persists until:
too high
Uneven
Controller auto-shutdown
Catch-All
User completes calibration using the app (sys then continues sensor check)
Note: Artoo will not assume the same error is present on
Powers off controller, or Solo
Remaining rare but problematic APM errors
Move Solo to a level surface
Altitude
calibrating
restart, and will run a fresh check when connected to Solo.
will be captured under a catch-all for
Controller auto-shutdown
logging trouble tickets
Please wait
Note: Artoo will not assume the same error is present on
restart, and will run a fresh check when connected to Solo.
required
Level error
User is asked to use Solo app to calibrate
Level error
Alert persists until:
User is asked to use Solo app to calibrate
User complete calibration using the app (sys then continues sensor check)
Alert persists until:
Powers off controller, or Solo
User complete calibration using the app (sys then continues sensor check)
surface
Service
Controller auto-shutdown
Powers off controller, or Solo
Note: Artoo will not assume the same error is present on
Compass
error
Controller auto-shutdown
Use 3DR Solo app to log a trouble
restart, and will run a fresh check when connected to Solo.
ticket with customer support
Note: Artoo will not assume the same error is present on
Please calibrate compass using
restart, and will run a fresh check when connected to Solo.
the 3DR Solo app
Catch-All
Remaining rare but problematic APM errors
Sensor error screen
will be captured under a catch-all for
For sensor errors requiring user-initiated restart
logging trouble tickets
required
Level
error
Please calibrate level
using the 3DR Solo app
Control sticl error
Persists until:
Controller starts with stick values in range.
Altitude calibration
System self-calibrates altitude after altitude disparity
Alert persists until:
System self-calibrates (sys then continues sensor check)
Timeout: after 1 minute (?) (results in "sensor error" screen)
error
Altitude calibration
System self-calibrates altitude after altitude disparity
Alert persists until:
System self-calibrates (sys then continues sensor check)
Timeout: after 1 minute (?) (results in "sensor error" screen)
Solo
Compass error
User is asked to use Solo app to calibrate.
Alert persists until:
User completes calibration using the app (system then continues sensor
User powers off controller, or Solo
compass
Controller auto-shutdown
Note: Artoo will not assume the same error is present on
restart, and will run a fresh check when connected to Solo.
Compass error
User asked to use Solo app to calibrate.
Alert persists until:
User completes calibration using the app (sys then continues sensor che
Powers off controller, or Solo
too high
Controller auto-shutdown
Note: Artoo will not assume the same error is present on
restart, and will run a fresh check when connected to Solo.
Level error
User is asked to use Solo app to calibrate
Alert persists until:
Altitude calibration
System self-calibrates altitude after altitude disparity
User complete calibration using the app (sys then continues sensor chec
Alert persists until:
Powers off controller, or Solo
System self-calibrates (sys then continues sensor check)
surface
Controller auto-shutdown
Timeout: after 1 minute (?) (results in "sensor error" screen)
Note: Artoo will not assume the same error is present on
restart, and will run a fresh check when connected to Solo.
Catch-All
Remaining rare but problematic APM errors
Compass error
will be captured under a catch-all for
User asked to use Solo app to calibrate.
logging trouble tickets
Alert persists until:
User completes calibration using the app (sys then continues sensor check)
required
Powers off controller, or Solo
Controller auto-shutdown
Note: Artoo will not assume the same error is present on
restart, and will run a fresh check when connected to Solo.
Level error
User is asked to use Solo app to calibrate
Alert persists until:
User complete calibration using the app (sys then continues sensor check)
Powers off controller, or Solo
Controller auto-shutdown
Note: Artoo will not assume the same error is present on
restart, and will run a fresh check when connected to Solo.
Sensor error screen
For sensor errors requiring user-initiated restart
32
Publicité
