Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
A S S E M B LY I N S T R U C T I O N S
Madison Vinyl Gate Kit w/ Fence Wings
(Unassembled) 62" Wide x 30" Tall
This Gate is designed to be integrated with our 30" High Madison Picket Fence
Please read through before starting assembly.
IMPORTANT: CHECK THE INSIDE OF THE LARGER PIECES IN YOUR BOX FOR OTHER MATERIALS
PACKED INSIDE.
Check Box for These Contents
In the event of missing or defective parts please call our customer service department at 1 877 778 5733 (Mon. to Fri. 8:00 AM to 4:00 PM EST).
1. Post Caps (6)
2. Posts (4) - 7/8" x 1
1/2
" x 43
3. Horizontal Rails - Top (2) - 1
4. Horizontal Rails - Bottom (2) - 1
5. Picket 1 (4) - ¼" x 1
1/2
" x 24
6. Picket 2 (2) - ¼" x 1
1/2
" x 22
7. Picket 3 (2) - ¼" x 1
1/2
" x 22
8. Picket 4 (1) - ¼" x 1
1/2
" x 21
9. Gate Posts (2) - 7/8" x 1
10. Gate Top Rail (1) - 1
1/2
" x 1
11. Gate Bottom Rail (1) - 1
12. Gate Hardware Kit with Fasteners (1)
13. Corner Brackets (4)
14. 3/4 in Self-Augering Stainless Steel Screws (48)
15. Zippity Connector Brackets (4)
16. 1/8" Drill Bit (1)
Tools You Will Need
• Cordless Drill
• Level
• Shovel
1/2
"
1/2
1/2
" x 1
" x 12"
1/2
1/2
" x 1
" x 12"
"
1/8
"
7/8
"
1/8
"
7/8
1/2
1/2
" x 26
"
1/2
" x 36
3/8
"
1/2
1/2
" x 1
" x 36
3/8
"
12
in
1/8
2 in
6
1
2
3
9
10
11
4
12
13
14
36
in
7/8
2
in
1/2
39
3/8
in
40
in
7/8
5/8
in
5
7
6
8
15
16
12
in
1/8
1
Not to Scale
Ver 1.5/061818
Publicité
Sommaire des Matières pour Zippity Madison
- Page 1 (Unassembled) 62” Wide x 30” Tall 2 in This Gate is designed to be integrated with our 30” High Madison Picket Fence Please read through before starting assembly. IMPORTANT: CHECK THE INSIDE OF THE LARGER PIECES IN YOUR BOX FOR OTHER MATERIALS PACKED INSIDE.
- Page 2 See illustration below. The weight strain will be transferred unto two posts versus just one. Installing fence panels on both sides of your gate is the ideal in all situations. Use Zippity clips to attach the gate to the fence panel posts. ...
- Page 3 S T E P O N E Assemble the Gate Frame Orientate the posts so the tab is facing up as illustrated. Insert the post down through the top and bottom horizontal rails as illustrated. Note that the underside of the bottom rail only has two holes as shown.
- Page 4 S T E P T W O Pickets and Caps Installation Insert pickets (as numbered in illustration) down through the top rail and into the bottom rail. Pressure fit the two caps down over the posts. The post caps will lock into place. Picket 2 Picket 4 Picket 2...
- Page 5 S T E P T H R E E Hinges and Latch Installation Align the hinges on the top and bottom horizontal rails as shown. Pre-drill two holes on the face of the horizontal rails for each hinge as shown. Holes should be approximately 1/4” from the edge of the rail as shown.
- Page 6 S T E P F O U R Assemble the Gate Wings Orientate the posts so the tab is facing up as illustrated. Insert the post down through the top and bottom horizontal rails as illustrated. Note that the underside of the bottom rail only has two holes as shown.
- Page 7 S T E P F I V E Install Gate wings into Ground Move the gate wings to their final location and identify the location of posts. The distance between the posts should be 39 ” or “ center-to-center Loosen the top 6” to 8” of the ground using a claw hammer and screw driver (or something equivalent) as illustrated.
- Page 8 S T E P F I V E Install Gate wings into ground - continued Level the assembled unit and backfill and compact dirt around the base of each post to strengthen the unit. Finish the assembly by pushing the post caps down over the top of posts as illustrated.
- Page 9 S T E P S I X Gate Installation Align the gate hinges against the horizontal rails of the gate wing as illustrated. Mark and pre-drill two holes for each hinge. Fasten each hinge with two screws. Align the catch as shown and pre-drill two more holes into the gate wing horizontal rail.
- Page 10 S T E P S E V E N Fence Panels installation Follow the instructions included in your Madison Picket Fence kit. Connect the top and bottom rails of the gate and fence panels using the supplied zippity clips as shown.
- Page 11 (103,8 cm) (16,8 cm) Cette barrière est conçue pour être intégrée avec notre clôture Madison de 30” (76,2 cm) de haut S.V.P. lire au complet avant de commencer l'assemblage. IMPORTANT: VÉRIFIEZ L'INTÉRIEUR DES PIÈCES PLUS LARGES CONTENUES DANS VOTRE BOÎTE POUR TOUS LES AUTRES MATÉRIAUX EMBALLÉS LÀ-DEDANS.
- Page 12 à deux poteaux plutôt qu'un seul. L'installation de panneaux de clôture à chaque bord de votre barrière est l'idéal dans toutes le situations. Utilisez les agrafes Zippity pour fixer la barrière aux poteaux de panneaux de clôture. ...
- Page 13 P R E M I È R E É T A P E Assemblez la charpente de barrière Orientez les poteaux pour que les languettes font face au haut comme illustré. Insérez les poteaux vers le bas à travers les barres horizontales supérieure et inférieure comme illustré.
- Page 14 D E U X I È M E É T A P E Installation des lattes et capuchons C'est facile! Insérez les lattes (comme numérotées dans l'illustration) vers le bas à travers la barre supérieure et dans la barre inférieure. Fixez sous pression les deux capuchons sur les poteaux.
- Page 15 T R O I S I È M E É T A P E Installation de charnières et verrou C'est facile! Alignez les charnières sur les barres horizontales inférieure et supérieure comme illustré. Pré-creusez deux trous sur la face des barres horizontales pour chaque charnière comme illustré.
- Page 16 Q U A T R I È M E É T A P E Assemblez les ailerons de barrière Orientez les poteaux pour que les languettes font face au haut comme illustré. Insérez les poteaux vers le bas à travers les barres C'est facile! horizontales inférieure et supérieure comme illustré.
- Page 17 C I N Q U I È M E É T A P E Installez les ailerons de barrière dans le sol Placez les ailerons de clôture dans leur position finale et identifiez le placement des poteaux. La distance entre poteaux devrait être 39 3/8" C'est facile! (100 cm) ou 40 7/8"...
- Page 18 C I N Q U I È M E É T A P E Installez les ailerons de barrière dans le sol - continué C'est facile! Nivelez l'unité assemblée et remblayez la base de chaque poteau avec la terre creusée et compactez-la pour renforcer l'unité. Finissez l'assemblage en poussant les capuchons vers le bas sur les bouts de poteau comme illustré.
- Page 19 S I X I È M E É T A P E Installation de barrière Alignez les charnières de barrière contre les barres horizontales de l'aileron de clôture comme illustré. C'est facile! Marquez et pré-creusez deux trous pour chaque charnière. Fixez chaque charnière avec deux vis.
- Page 20 Madison. Connectez les barres inférieures et supérieures de la barrière et des panneaux de clôture avec les agrafes de jointure Zippity comme illustré. 701 chemin Lawton , Charlotte NC USA 28216 www.zippity-outdoor.com Tél sans frais: 1 877 778 5733 Fax: 704 631 4685...