Publicité
Les langues disponibles
Les langues disponibles
MAINTENANCE AND REPAIR INSTRUCTIONS
CHAIN BRAKE® TEST
Before cutting with your saw, the Chain Brake® should
be tested as follows:
A. Make sure the Chain Brake® is disengaged (Fig. 26).
B. Place the saw on a firm, flat, dry surface that is clear
of any debris. Do not let the saw come in contact
with any objects.
C. Plug the unit into the power source.
D. Grasp the front handle (not the Chain Brake®/Hand
Guard Lever) with your left hand. Thumb and fingers
should encircle the handle.
E. Grasp the rear handle with your right hand. Thumb
and fingers should encircle the handle.
F. Depress the LOCK/OFF button with your right thumb.
Squeeze the trigger with your index finger (Fig. 7).
G. While the motor is running, activate the Chain
Brake® by rolling your left hand forward against the
lever.
H. Chain and motor should stop abruptly.
WARNING:
when the Chain Brake® is engaged, take
the saw to the nearest Authorized Service
Center. Do not use the saw if the Chain
Brake® is not in proper working order.
EXTENSION CORDS
When using an electric chain saw, plug it into the
extension cord only when you are ready to cut wood.
Connect the extension cord to a 110/120 voltage outlet.
Refer to the Electrical Safety Warnings section.
CAUTION:
overloaded.
WARNING:
damp environment. Do not expose the saw to
rain, snow or sleet. Moisture will cause short
circuits. Replace or repair any damaged or
frayed extension cords before using your saw.
Keep the cord away from the cutting area and
position the cord so that it will not be caught
on branches or other objects during cutting.
If the chain and
motor fail to stop
A cord that is hot to
the touch is
Do not operate your
chain saw in a wet or
DOUBLE INSULATION
WHEN SERVICING, USE ONLY IDENTICAL
REPLACEMENT PARTS.
Information
Do not use if the cord or plug is damaged. Your
appliance is double insulated to help protect against
electric shock. Double insulation construction consists of
2 separate "layers" of electrical insulation.
Appliances built with this insulation system are not
intended to be grounded. As a result, the extension cord
used with your appliance can be plugged into any
conventional 120 volt electrical outlet.
Normal safety precautions must be observed when
operating an electrical appliance. The double insulation
system is only for added protection against injury resulting
from a possible internal electrical insulation failure.
WARNING:
has no serviceable parts inside. Do not
attempt to repair it yourself. For service
information, dial 1-800-668-1238.
In this double insulated appliance, 2 systems of insulation,
instead of grounding, are provided. No grounding means
is provided on a double insulated appliance, nor should a
means for grounding be added to the appliance. No
serviceable parts are inside. A double insulated appliance
is marked with the words, "DOUBLE INSULATION" or
"DOUBLE INSULATED." The symbol (square within a
square) may also be marked on the appliance.
Maintenance
1. Place switch in OFF position and unplug the power
supply before the appliance is serviced, cleaned, or
maintenance is performed.
2. Keep the air intake clean and air vents free of debris
to avoid overheating the motor.
3. Clean with a damp sponge and mild soap. Do not
squirt with a water hose or douse with water or other
liquids.
4. Inspect the saw chain for proper tension before each
use and frequently during cutting. Sharpen as required.
5. Clean the guide bar and bar pad to ensure free path
for oil.
6. No motor lubrication is necessary. The motor is
equipped with lifetime lubricated bearings.
7. If the saw does not operate, turn switch to OFF
position and disconnect the extension cord, first from
the power supply, then from the saw. Check the
power supply for blown fuses or tripped circuit
breakers. If it still does not operate, contact a
Product Service Department. Call 1-800-520-520 for
more information.
Do not attempt to repair it yourself. No serviceable
parts are inside.
16
Your double
insulated appliance
Publicité
