EINHELL 4465191 Mode D'emploi page 11

Separately available accessories
18V 1.5Ah PXC Lithium-Ion battery
18V 2.0Ah PXC Lithium-Ion battery
18V 2.5Ah PXC Lithium-Ion battery
18V 3.0Ah PXC Lithium-Ion battery
18V 4.0Ah PXC Lithium-Ion battery
18V 3.0Ah PXC Plus Lithium-Ion battery
18V 4.0Ah PXC Plus Lithium-Ion battery
18V 5.2Ah PXC Plus Lithium-Ion battery
18V 4.0Ah/6.0Ah PXC Plus Lithium-Ion battery
18V 5.0Ah/8.0Ah PXC Plus Lithium-Ion battery
18V PXC Dual Port Fast Charger
18V PXC Fast Charger
Contact your local retailer for more specifi c
models of batteries and charger available in your
area. You can also explore battery + charger
options at Einhell.com.
3. Intended use
The equipment is designed for cutting and
sanding/grinding of wood, iron, plastic and
similar materials using the appropriate abrasive
paper. Furthermore, the equipment is intended
for sawing wood, plastic and similar materials,
as well as scraping off glued carpets, fi lling
compound residues, old paint and similar
applications.
The equipment is allowed to be used only for its
prescribed purpose. Any other use is deemed to
be a case of misuse. The user/operator and not
the manufacturer will be liable for any damage or
injuries of any kind resulting from such misuse.
4. Technical data
Motor power supply: ............................ 18V
No-load OPM ................................ 22.000-40.000
No-load speed RPM ..................... 11.000-20.000
Sanding/grinding
area: .......................................... 3.5'' x 3.5'' x 3.5''
Oscillation angle: ...........................................3.2°
Weight (Tool only): .....................................2.4 lbs
Wear ear-muff s.
The impact of noise can cause damage to
hearing.
Anl_TP_MG_18_Li_BL_SPK7_NA.indb 11 Anl_TP_MG_18_Li_BL_SPK7_NA.indb 11
EN
Reduce noise generation and vibration to a
minimum!
•
Use only equipment that is in perfect
condition.
•
Maintain and clean the equipment regularly.
•
Adapt your way of working to the equipment.
•
Do not overload the equipment.
•
Have the equipment checked if necessary.
•
Switch off the equipment when not in use.
CAUTION!
Residual risks
Even if you use this electric power tool in
accordance with the instructions, certain
residual risks cannot be eliminated. The
following hazards may arise in connection
with the equipment's construction and
layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear
protection is applied.
3. Health damage caused by hand-arm
vibrations if the equipment is used over a
longer period or is not properly guided and
maintained.
5. Before starting the equipment
Warning!
Always remove the battery pack before making
adjustments to the equipment.
Be sure to read the following information before
you put the cordless equipment into operation:
•
Charge the battery pack with the charger
(battery and charger not included). An empty
battery pack requires a charging period of
approximately 0.5 to 1 hour.
5.1 Fitting the plug-in tools (Fig. 1-5)
•
Open the quick-release lock for changing
tools (5) as shown in Fig. 2.
•
To fit the plug-in tools safely you should hold
the multi-tool so that the On/Off switch (1)
points down and the tool chuck (2) faces up.
•
Place the plug-in tool (e.g. the scraper) on
the tool chuck (2) so that the pins of the tool
chuck fit into the recesses in the plug-in tool.
The tool chuck (2) is magnetic in order to
secure the plug-in tool during the clamping
procedure.
- 11 -
19.10.2023 10:32:41 19.10.2023 10:32:41