Ravelli DUAL 9 SUPER Manuel D'utilisation Et D'entretien page 61

The first setting allows the activation of the CLIMATE COMFORT function. This function is intended to ensure that the room tem
-perature set is maintained steady upon setting the maximum period of "X" minutes (SWITCH-OFF DELA
Y: 5 MIN) before switch-ing to ECO STOP phase. The STOVE maintains this state until the temperature drops below the set
VENTILATION menu (function only for models in which the same is specified in the dedicate user's manual) Rev.1 26/03/2018
value (CLIMATE COMFORT DELTA : 5 ).
For example, with the room temperature at 21 ° C, the stove switches of f when this temperature is
Pag.61
The stoves equipped with ventilation system can heat the area in which are installed through the heat generated by the window and
EN
reached and restarts when the temperature reaches 15°C (21°C - 5°C - 0,5°C tolerance).
the room temperature fan installed inside them.
You can also activate the function using an external thermostat, keeping in mind that this does not include the value of the hyster
-esis.
Below are the messages shown on display when the stove is equipped with ventilation system.
The first setting allows the activation of the CLIMATE COMFORT function. This function is intended to ensure that the room tem
We recommend you use an external thermostat with a histeresys value that can be set to maximum 3°C.
perature set is maintained steady upon setting the maximum period of "X" minutes (SWITCH-OFF DELA Y: 5 MIN) before switch-ing
The operation of the stove could activate the switch ON/OFF phases for several times during the day;
to ECO STOP phase. The STOVE maintains this state until the temperature drops below the set value (CLIMATE COMFORT DELTA:
The temperature read by the handheld unit controls the modulation of the stove. If you want to adjust the ventilation by
this may affect the service life of the ignition coil.
5°C). For example, with the room temperature at 21 ° C, the stove switches of f when this temperature is reached and restarts when
adjusting the stove, set the fan to A mode as shown in the relative chapter.
the temperature reaches 16°C (21°C - 5°C). You can also activate the function using an external thermostat, keeping in mind that this
USING THIS METHOD, IT IS NECESSARY TO VERIFY THAT AFTER EACH AUTOMATIC SHUTDOWN
THE GRATE IS ALWAYS VERY CLEAN TO GUARANTEE CORRECT AUTOMATIC SWITCH ON.
does not include the value of the hysteresis.
AUTOMATIC SWITCH ON.
Description of menu functions
Description of menu functions
Press the key to access the MENU page
Press the key
"access menu" to
access the
MENU page
The TECHNICIAN and MANUFACTURER menus are protected by password.
To exit the page and return to Stand-by page, press the button repeatedly.
Chronothermostat
Chronothermostat
Control: ventilation can be set from 0 to AUTO where 0 indicates that the same is disabled, setting from MIN to MAX enables selecting
the heat distribution speed. If set to AUTO, the ventilation follows the power set on the stove. With the Chrono-thermostat function you can program the automatic switch ON/OFF of the stove for each day of the week
for each day of the week in 4 independent time intervals (SET CHRONO 1-2-3-4)
Chrono function Below are given the steps for accessing the relative menu starting from Stand-By mode.
By enabling the chrono function, it is possible to control the ventilation speed for each program as shown in the logic above.
MENU
MANUFACTURER
USER
MANUFACTURER'S
TECHNICIAN
Press the key "access
menu" to access
Press the key
the
"access menu" to
MENU page
access the
MENU page
CHRONO
CHRONO
ENABLE CHRONO
ENABLE CHRONO SET CHRONO
SET CHRONO
SET CHRONO 1
SET CHRONO 2
SET CHRONO
SET CHRONO 3
SET CHRONO
SET CHRONO 4
CHRONO
CHRONO
ENABLE CHRONO
SET CHRONO 1
ENABLE CHRONO
SET CHRONO 2
SET CHRONO 1
SET CHRONO 3
SET CHRONO 2
SET CHRONO 4
SET CHRONO 3
SET CHRONO 4
The exit key shows the CHRONO menu to set other variables related to the menu functions.
To exit the page and return to Stand-by page, press the button repeatedly.
Pages displayed upon the activation of advanced layouts
By activating a layout different from the standard (layout 0), even if maintaining the same functions of the menu, the "Stand-by" page will
display all connected utilities such as the temperature of the boiler of the puffer.
Below is shown the new display mode and the function of every icon for every layout, to change the various settings.
If the type of system designed requires controlling the 3-way valve (diagram 1 and 3), it is necessary to purchase the
optional kit from the retailer or the authorized Ravelli dealer.
Use and maintenance manual Dual 9 super
MENU
USER
MANUFACTURER'S
TECHNICIAN
VENTILATION POW.
MENU
USER
ENGINEER
Press the key
"confirm"
Press the key
to access the
"confirm"
USER page
Manuale utente PALMARE IDRO TOUCH RADIO
to access the
USER page
POWER SETTING
CHRONOTHERMOSTAT
SCREW LOADING
SET AIR-PELLET
Press the key
"confirm"
MENU to access the
USER page
USER
MANUFACTURER
ENGINEER
Press the increase/decrease keys
to change the ventilation.
USER
SCREW FEEDING
USER
CHRONOTHERMOSTAT
AIR-PELLET SET
POWER SETTING
STOVE STATE
CHRONOTHERMOSTAT
SCREW LOADING
SET AIR-PELLET
ENABLE CHRONO
ENABLE CHRONO
Press the key
"enter" at the end of the
setting, from the following
CHRONO page
USER
Press the key
"confirm"
to quickly switch to
VENTILATION.
"increase/decrease"
CHRONOTHERMOSTAT
POWER SETTING
CHRONOTHERMOSTAT
SCREW LOADING
Press the key
"selection"
Press the key
to quickly switch to
several times
CRONO-THERMOSTAT.
to quickly switch to
CRONO-THERMOSTAT.
ENABLE CHRONO
ENABLE CHRONO
VENTILATION POW.
USER
SCREW FEEDING
USER
AIR-PELLET SET
STOVE STATE
SET AIR-PELLET
Vers. 01 del 07/04/15
Pag.33
Press the increase/decrease keys
"increase/decrease"
to change the ventilation.