Heco AURORA 200 P Mode D'emploi page 13

Connecting the power supply of the transmitter and the active speaker
Included in delivery is the most commonly used mains cable. The mains cable used in your country, however, may be different.
If the mains cable is not compatible with your power sockets or if you are in any doubt, please contact your Heco dealer.
1.
Insert the 3-pin mains cable into the socket of the active speaker (Fig. 2, (3)).
2.
Insert the mains cable into the socket. Make sure that you are using the mains plug that is compatible with the socket
(refer to the information above).
OPERATION
As soon as the device is connected to the power supply and the power switch (Fig. 2, (2)) has been turned on, the STBY LED on the
active loudspeaker lights up red. The speaker is then in stand-by mode. 5 difference audio sources can be connected to the active
loudspeaker at the same time via the outputs (6), (7), (8), (9) and Bluetooth. The speaker is switched on using the remote control
(Fig. 3, (13)) and an audio source selected using the button (19). The volume is regulated via the button (14), the speaker can be
switched to mute using button (18). With the BASS (16) and TREBLE (15) buttons, the bass and treble levels can be adjusted to the
set-up and your own personal listening taste. The LINEAR button is used to reset the bass and treble control to the neutral position.
Alternatively, the loudspeaker can be operated on the active speaker's rear connection panel (Fig. 2). Pressing the VOLUME/
SOURCE control (10) the first time switches on the active speaker, pressing it again selects the inputs in turn. The volume is
regulated by turning the control. Prolonged pressing switches the loudspeaker to stand-by mode.
Please note:
All Heco loudspeakers are designed and built for optimum sound reproduction with the tone controls in the central position – i.e.
with "linear" amplifier output. Turning up the bass and treble controls too far delivers more power to the woofers and/or tweeters,
and at high volumes this can actually destroy the speaker units! Always turn the volume down immediately as soon as you hear
distortion!
CAUTION
Interfering with the speaker or accessories shall result in the expiration of the operating licence. The supplied accessories are to be
used for operation. Additional accessories must be intended for the purpose at hand and in perfect working order.
AUTO STANDBY FUNCTION
The unit has an Auto Standby function that automatically switches the device to stand-by mode if no audio signal is detected on
the inputs over a period of approx. 60 minutes. This function implements an EU energy-saving regulation (1275/2008 EG), reducing
power consumption if the device is accidentally left turned on after use.
This function can be deactivated as follows:
Press the MUTE button on the remote control. Then keep the Volume/Source control at the rear of the right speaker depressed
for 5 seconds and release it. The green LED flashes twice in the display as confirmation. The Auto Stand-by function has been
deactivated.
Repeat the procedure to re-activate the Auto Stand-by function. The green LED flashes once in the display as confirmation.
SPECIFICATIONS
Configuration:
Speaker assembly:
Output power (RMS/Max.):
Frequency range:
Crossover frequency:
Operating frequency:
Maximum emitted power
(EN 62479):
Mains voltage:
Dimensions (WxHxD) active speaker:
Dimensions (WxHxD) passive speaker:
Weight active speaker:
Weight passive speaker:
SUBJECT TO TECHNICAL CHANGE.
AURORA 200 P
2-way bass reflex, active
5" woofer-midrange
1" dome-tweeter
2 x 35 / 2 x 70 watts
38 – 40.000 Hz
3.400 Hz
2402 – 2480 MHz
2.5 dBm
100 – 240 V
170 x 308 x 258 mm
170 x 308 x 245 mm
5.8 kg
5.2 kg
13