Télécharger Imprimer la page

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Operating Instructions
Series SW/TW7000 Welding Hose Reels
Low Pressure Model Numbers:
TW7400 OLP
TW7450 OLP
TW7400 OLPT
TW7450 OLPT
Dimensions
SAFETY
Personal injury and/or equipment damage may result if proper safety
precautions are not observed.
• Ensure that reel is properly installed before connecting input and
output hoses.
• Bleed fluid/gas pressure from system before servicing reel.
• Before connecting reel to supply line, ensure that pressure does
not exceed maximum working pressure rating of reel.
• Remember, even low pressure is very dangerous and can cause
personal injury or death.
• Be aware of machinery and personnel in work area.
• If a leak occurs in the hose or reel, remove system pressure
immediately.
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605
Customer Service: 855-634-9109 • reelcraft@reelcraft.com • www.reelcraft.com
TW7460 OLP
SW7600 OLPT
TW7460 OLPT
SW7650 OLPT
A
20 1/4"
B
19 3/4"
C
7 7/8"
D
3 7/8"
E
7 3/8"
IMPORTANT
Read this manual carefully before installing, operating or
servicing this equipment.
Models TW7400 OLP, TW7400 OLPT, and
SW7600 OLPT are listed to UL 1351.
• A high tension spring assembly is contained within the reel.
Exercise extreme caution.
• Pull hose from reel by grasping the hose itself, not the control
valve.
• Ensure that reel, hose, and equipment being serviced are
properly grounded. Use an ohmmeter to check ground
continuity.
• If reel ceases to unwind or rewind, remove system pressure
immediately. Do not pull or jerk on hose!
• Treat and respect the hose reel as any other piece of machinery,
observing all common safety practices.
Form# 834-696A Rev: 7/2020

Publicité

loading

Sommaire des Matières pour Reelcraft TW7450 OLPT

  • Page 1 • Treat and respect the hose reel as any other piece of machinery, observing all common safety practices. Form# 834-696A Rev: 7/2020 Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725 Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605 Customer Service: 855-634-9109 • reelcraft@reelcraft.com • www.reelcraft.com...
  • Page 2 1. Unpack and inspect reel for damage. Turn by hand to check for smooth operation. Check for completeness. 2. Configure reel for top, side, or bottom-wind hose dispensing by removing bolts (or nuts) (1) securing guide arm bracket (2). Caution: When changing guide arm positions, the Page 2 www.reelcraft.com...
  • Page 3 User servicing of the reel is limited to replacing the input/ output hoses or swivel only. Refer all other repairs to an autho- rized service person or directly to Reelcraft Industries, Inc. Failure to do so can result in personal injury and/or equipment damage and may void the warranty.
  • Page 4 Max. Operating Pressure 200 PSI 200 PSI 200 PSI 200 PSI 200 PSI 200 PSI 200 PSI 200 PSI Max. Operating Temperature 150 °F 150 °F 150 °F 150 °F 150 °F 150 °F 150 °F 150 °F www.reelcraft.com Page 4...
  • Page 5 • Dentro del carrete puede estar contenida una unidad de resorte de alta tensión. Tenga extremo cuidado. Form# 834-696A Rev: 7/2020 Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725 Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605 Customer Service: 855-634-9109 • reelcraft@reelcraft.com • www.reelcraft.com...
  • Page 6 Entrada de MONTAJE acetileno/gas combustible, 6.4 ATENCIÓN: A menos que el carrete se hubiera especificado de mm (1/4”) FPT manera diferente al pedirlo, la máxima altura de la instalación es 4.88 m (16 pies). No supere esta distancia. www.reelcraft.com Page 6...
  • Page 7 únicamente al reemplazo de las mangueras de entrada/salida o la rótula. Dirija todas las demás reparaciones a una persona de servicio autorizada, o directamente a Reelcraft Industries, Inc. Si no lo hace pueden producirse lesiones personales y/o daños a los equipos, y puede anular la garantía.
  • Page 8 Max. Presion de Operacion 200 PSI 200 PSI 200 PSI 200 PSI 200 PSI 200 PSI 200 PSI 200 PSI Max. Temperatura de Operacion 150 °F 150 °F 150 °F 150 °F 150 °F 150 °F 150 °F 150 °F Page 8 www.reelcraft.com...
  • Page 9 Form# 834-696A Rev: 7/2020 Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725 Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605 Customer Service: 855-634-9109 • reelcraft@reelcraft.com • www.reelcraft.com...
  • Page 10 ATTENTION : Sauf si le dévidoir avait été spécifié différemment à sa commande, la hauteur maximale pour son installation est de 16’ (4,9 m). Ne dépassez pas cette longueur. Observez toutes les normes applicables, NEC, OSHA et locales, pour l’installation de cet équipement. Page 10 www.reelcraft.com...
  • Page 11 Confiez toutes les autres réparations à un agent de service agréé, ou directement à Reelcraft Industries, Inc. Sinon vous risquez des blessures corporelles et/ou des dommages sur l’équipement, et cela peut annuler la garantie.
  • Page 12 Pression de service maximum 200 PSI 200 PSI 200 PSI 200 PSI 200 PSI 200 PSI 200 PSI 200 PSI Température de service maximum 150 °F 150 °F 150 °F 150 °F 150 °F 150 °F 150 °F 150 °F www.reelcraft.com Page 12...