Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Operating Instructions
Safe-T-Reel Welding Hose Reels
Model Numbers:
T-1225-04
T-1225-04-100T
Dimensions
A
B
19"
18"
B
A
Four 1/2" diameter mounting holes
SAFETY
Personal injury and/or equipment damage may result if proper safety
precautions are not observed.
• Bleed fluid/gas pressure from system before servicing reel.
• Before connecting reel to supply line ensure that supply line
pressure does not exceed maximum rated working pressure of
reel.
• Ensure that reel is properly installed before connecting to supply
line (see installation instructions).
• Do not wear loose fitting clothing while operating reel.
• Be aware of other personnel in work area.
• Pull hose from reel by grasping the hose itself, not the work
device.
• If a leak occurs in the hose or reel, remove supply line pressure
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605
Customer Service: 855-634-9109 • reelcraft@reelcraft.com • www.reelcraft.com
T-1226-06
C
D
E
6"
6-1/2"
16-1/4"
E
D
C
IMPORTANT
Read this manual carefully before installing, operating or
servicing this equipment.
immediately.
• If reel ceases to unwind or rewind, remove pressure immediately.
Do not pull or jerk on the hose!
• Treat and respect the hose reel as any other piece of machinery,
observing all common safety practices.
Form# 1104-801 Rev: 7/2018
Publicité
Table des Matières
Manuels Connexes pour Reelcraft T-1225-04
Sommaire des Matières pour Reelcraft T-1225-04
- Page 1 • If a leak occurs in the hose or reel, remove supply line pressure Form# 1104-801 Rev: 7/2018 Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725 Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605...
-
Page 2: Installation Instructions
Fully extend and charge hose before winding onto reel. Momentarily open control valve, when initially charging to purge hose of gases. When fluid appears at control valve, close valve. This prevents flattening of the hose and excessive pressure on the drum when fluid supply is reinitialized at a later time. Page 2 www.reelcraft.com... - Page 3 Safe-T-Reel Welding Hose Reels Item Description T-1225-04 T-1225-04-100T T-1226-06 1 Spool Cover 261517 261517 261517 2 Hex Cap Screw S2-85 S2-85 S2-85 3 Spool Half (Handle) 261521-R 261521-R 261521-R 4 Self Tapping Screw S285-14 S285-14 S285-14 5 Handle Post 261515...
-
Page 4: Dimensions
• No use vestimenta suelta cuando maneje el carrete. Form# 1104-801 Rev: 12/2014 Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725 Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605 Customer Service: 855-634-9109 • reelcraft@reelcraft.com • www.reelcraft.com... - Page 5 Cuando aparezca el fluido en la válvula de control, ciérrela. Esto impide el aplanamiento de la manguera y la aplicación de una presión excesiva sobre el tambor cuando se reinicie más adelante el suministro de fluido. www.reelcraft.com Page 5...
- Page 6 Safe-T-Reel carretes de la manguera de la soldadura Ítem DESCRIPCIÓN T-1225-04 T-1225-04-100T T-1226-06 N° Cubierta de bobina 261517 261517 261517 Perno S2-85 S2-85 S2-85 Manija de mitad de bobina 261521-R 261521-R 261521-R Tornillo autorroscante S285-14 S285-14 S285-14 Soporte de manija...
-
Page 7: Consignes D'utilisation
• Même à basse pression c’est très dangereux et peut causer des dommages irréparables ou la mort. Form# 1104-801 Rev: 7/2018 Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725 Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605 Customer Service: 855-634-9109 • reelcraft@reelcraft.com • www.reelcraft.com... -
Page 8: Montage De Tous Les Enrouleurs De Tuyau
à la mise en charge initiale pour purger les gaz du tuyau. Quand le fluide apparaît refermer cette vanne. Cela évite l’aplatissement du tuyau et une pression excessive sur le tambour si l’alimentation en fluide est réinitialisée ultérieure- ment. Page 8 www.reelcraft.com... - Page 9 Safe-T-Reel dèvidoirs de tuyau de soudure N° de Description QTÉ T-1225-04 T-1225-04-100T T-1226-06 RÉF Couvercle de tambour 261517 261517 261517 Boulon S2-85 S2-85 S2-85 Moitié de tambour (poignée) 261521-R 261521-R 261521-R Vis autotaraudeuse S285-14 S285-14 S285-14 Tige de poignée 261515...