Publicité
Les langues disponibles
Les langues disponibles
WARNING: Wheels used for cutting may break or kick
back if they bend or twist while the tool is being used to
do cut‑off work.
WARNING: Do not bang or bump a cut‑off wheel
when starting or during a cut.
1. Grasp main handle
3
2. Line up wheel with material to be cut. Be sure nothing is
near or in line with the wheel.
3. Depress and hold trigger switch
wheel into work with firm pressure. Do not force the tool.
For maximum efficiency and wheel life, keep the wheel
speed high.
4. To stop tool, release trigger switch
If Using the Dust Shroud for Dust Collecting
(Fig. J)
1. Remove battery pack.
2. Adjust the depth of cut when using the dust shroud.
3. Insert the battery pack.
4. While cutting, keep the shoe flat against the workpiece
and maintain a firm grip, don't force the cut off tool
through the workpiece. Forcing a cut off tool can
cause kickback.
nOTE: If making a partial cut, restarting a cut, or
correcting cut direction. Allow the wheels to come to
a complete stop. To resume cutting, center the wheel
in the kerf (cutting slot)
cutting edge, pull the trigger and re‑enter the cut slowly.
5. To stop tool, release trigger switch.
Tool Connect™ Chip (Fig. K)
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your tool is Tool Connect™ Chip ready and has a location for
installation of a Tool Connect™ Chip.
Tool Connect™ Chip is an optional application for your
smart device (such as a smart phone or tablet) that connects
the device to utilize the mobile application for inventory
management functions.
Refer to Tool Connect™ Chip Instruction Sheet for
more information.
installing the Tool Connect™ Chip
1. Remove the retaining screws
Connect™ Chip protective cover
2. Remove the protective cover and insert the Tool
Connect™ Chip into the empty pocket
3. Ensure that the Tool Connect™ Chip is flush with the
housing. Secure it with the retaining screws and tighten
the screws.
4. Refer to Tool Connect™ Chip Instruction Sheet for
further instructions.
firmly.
4
then slowly feed
.
4
, back and saw away from
29
25
that hold the Tool
26
into the tool.
27
.
Transportation and Storage
During transportation and storage lock the trigger switch
with the lock‑off button.
Remove the battery pack during the tool storage.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your D
WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non‑metallic parts of the tool. These
chemicals may weaken the plastic materials used in
these parts. Use a cloth dampened only with water and
mild soap. Never let any liquid get inside the tool; never
immerse any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product,
e
use of such accessories with this product could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact D
(1‑800‑433‑9258) or visit our website: www.dewalt.com.
Lanyard Connection (Fig. A)
Optional Accessory
safety Warnings specific for Use At height
WARNING:
•
If the tool is dropped for any reason, the lanyard
attachment point and battery strap components
must be inspected and properly serviced prior to
re‑use. The lanyard attachment point is designed
to stretch to absorb the shock of a drop. Any
permanent stretch to the device exposing the
red marked internal coils indicates it has been
compromised and must be serviced prior to reuse.
•
Remove any wrenches/chuck keys and store them
separately when using at height.
•
Do not use hang hook as lanyard
attachment point.
English
e
WALT. Call 1‑800‑4‑D
WALT
e
e
WALT
13
Publicité
