Fortin CAN-SL2 Guide Rapide

Fonctionnal if equipped
Lock Tach
Unlock Start Enable
Arm Door Trigger
Disarm Trunk Trigger
Trunk Hood Trigger
2
Driver door pin
Tach
Ground Out
Lock
Ignition
LED
Front view of the module
Front view of the BCM
connector located on the driver
kick panel or above the
1 Brown/White
Grey
Grey/Black
Brown
conn.
1
Back view of the module
Connect wire to Remote-Starter/Alarm
Copyright © 2009, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED
NISSAN MAXIMA
INTELLIGENT-KEY
Radio Off Heat Seats
Transponder Bypass Gas Door
PK3, Passlock Window Roll Down
Slidding Door Hatch
Defrost Brake Signal
LED
8 1
Lt. Blue Lt. Blue/Black
White White/Black
~
Pink Pink/Black
~
Blue Green
Door + Trunk Trigger
Orange Orange/Black
N.C.
Purple
Purple/Black or Purple/White
Yellow Yellow/Black
14
7
20 19 18 17 16 15 14 13 12
acceleration pedal.
40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23
N.C.
(CAN High) Data
(CAN Low) Data
3
N.C.
OR / OU
Brown/White N.C.
(CAN High) Data
Grey
(CAN Low) Data
Grey/Black
Brown
N.C.
Connect wire to vehicle
Technical support:
TEL: 514-255-HELP (4357)
FAX: 514-255-1367
Web: www.ifar.ca
2007-2008
Vehicle security light
N.C.
* Only if the vehicle
Hood Trigger*
is equipped with
a hood pin.
N.C.
Unlock
Trunk
11 10 9 8 7 6 5 4 3 2 1
22 21
Blue
Pink
6
14
OUTPUT INPUT
Neither the manufacturer or distributor of this module is
responsible of damages of any kind indirectly or directly
caused by this module, except for the replacement of this
module in case of manufacturing defects. This module must
be install by qualified technician. This instruction guide may
change without notice. Visit www.ifar.ca to get latest version.
CAN-SL2
WEB
UPDATE Made in Canada - Rev. A - 14 / 01 / 2009
W e b s i t e
ALARM AND REMOTE STARTER CAN BUS INTERFACE KIT
Data-Link (1 way)
Connect: Connect:
8 1
Lt. Blue Lt. Blue
Lt. Blue/Black
White White
White/Black
Pink
Pink/Black
1
Blue Green Brown/White
Grey
Orange Orange/Black Orange
Grey/Black
Purple Purple/Black Purple
Brown
Yellow Yellow/Black Yellow
4
14
7
Make the connections of the CAN-SL2 to the
vehicle:
1
1.A
Connector 1 (Black):
Determine the type of installation:
INSTALLATION WITH DATA-LINK (see page 2)
INSTALLATION WITHOUT DATA-LINK (see page 2)
1.B
Connector 2 (White):
Make the connections
1.C
Connector 3 (White, located at the back of the module):
Make the connections
Press the programming switch while
inserting the main wires harness (
into the CAN-SL2 module.
The LED will illuminate to indicate you are
2
in programming mode, release the
programming button.
Connect
( CONN. 2
3
WARNING: Connector 2 can be easily
plugged in backwards.
Connect
4
( CONN. 3
5
Turn the key to the
Once the LED starts to flash rapidly
the key to the
6
The LED will turn off to indicate the
module has been programmed.
The module is now ready for use.
: h t t p : / / w w w . i f a r . c a
Data-Link (2 way)
8 1
Lt. Blue/Black
White/Black
Pink
Pink/Black
1
Blue Green Brown/White
Grey
Orange/Black
Grey/Black
Purple/Black
Brown
Yellow/Black
4
14
7
CONN 1 )
the other connectors
)
the other connectors
)
"ON" position .
turn
OFF position .