Télécharger Imprimer la page

Palram Amsterdam 2230 Instructions De Montage page 4

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 32
EN
Door Cover
Attention!
Please read these instructions carefully before you start to assemble this product.
Please carry out the steps in the order set out in these instructions.
Keep these instructions in a safe place for future reference.
Safety Advice
• For safety purposes we strongly recommend the product to be assembled by at least two people.
• Be sure to check that there are no hidden pipes or cables in the wall before drilling.
• Some parts may have sharp edges. Please be careful when handling components.
• Always wear gloves, shoes, safety goggles, and long sleeves when assembling or performing any
maintenance on your product.
• Do not attempt to assemble the product in windy or wet conditions.
• Do not attempt to assemble the product if you are tired, have taken drugs, medications or alcohol,
or if you are prone to dizzy spells.
• Dispose of all plastic bags safely - keep them out of reach of small children.
• Keep children away from the assembly area.
• When using a stepladder or power tools, make sure you follow the manufacturer's safety advice.
• Do not climb or stand on the roof.
• Do not hang or lay on the profiles.
• Keep roof and gutter clear of snow, dirt & leaves.
• Heavy snow load on roof can make it unsafe to stand below or nearby the product.
• If color was scratched during assembly it can be fixed.
Cleaning instructions
• In order to clean the product, use a mild detergent solution and rinse with cold clean water.
• Do not use acetone, abrasive cleaners, or other special detergents to clean the panels.
• Clean the product once assembly is complete.
Before Assembly:
• Choose your site carefully before beginning assembly.
• Consider the door's opening - inside or outside.
• Sort the parts and check against the content parts list.
• Parts should be laid out close at hand. Keep all small parts (screws etc.) in a bowl so they do not
get lost.
• Please consult your local authorities if any permits are required prior to constructing the product.
Please note: Steps marked with dashed outlines refer to Extensions only.
• It is possible to install up to three products joined together.
• Please note the sizes needed in order to place and connect the brackets to the wall.
• Some of the steps are irrelevant for an assembly of a single canopy.
• When assembling a single or an extended canopy, some parts may be surplus.
Additional information:
• Please apply silicone sealant if needed
• During assembly, use a soft surface below the parts to avoid scratches and damages.
• You are solely responsible for determining whether the handling, storage, assembly, installation
or use of this product is safe and appropriate in any location or for any given application. The
manufacturer is not responsible for any damages or injury to you, any other person or any
property resulting from the improper handling, storage, installation, assembly or use of this
product, or the failure to follow the manufacturer's written instructions regarding the handling,
storage, installation, assembly and use of this product. This product is intended for normal
residential use only. Do not use this product for any application that is not recommended in
these instructions or building codes in effect in location where this product will be used. Always
take care and use appropriate safety equipment (including eye protection) when assembling or
installing this product.
During Assembly
When encountering the information icon, please refer to the relevant
assembly step for additional comments and assistance.
Note: Use only the parts registered in the content list, some parts may be surplus.
Step 1: Important! Please make sure the frame is perfectly centered before fixing.
Step 4: Please apply silicone sealants above beam 8288, in order to prevent water from seeping in.
Step 17: Please make sure you install the panels with the UV protected side out (marked with
"THIS SIDE OUT") and remove the sticker as panels are in place.
Step 20: Please apply silicone sealant on the inner part of 8167 and connect to the profile.
Step 21: Note: when assembling an extansion, some parts and screws will be surplus.
* Please tighten all screws when completing assembly.
Note!
The wall anchoring kit supplied with this product is suitable for concrete or solid
brick walls. Other wall types need an accordant wall fixation kit.

Publicité

loading