Ryobi RSDP4 Mode D'emploi page 3

Safety, performance, and dependability have been given top
priority in the design of your screwdriver.
INTENDED USE
The screwdriver is intended to be used only by adults who
have read and understood the instructions and warnings in
this manual, and can be considered responsible for their
actions.
The product is intended for fastening and removing screws
and bolts.
The product is intended for consumer use only.
Do not use the product for any other purpose. Use of the
product for operations diff erent from intended could result in
a hazardous situation.
WARNING! Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
SCREWDRIVER SAFETY WARNINGS
■
Hold the power tool by insulated gripping surfaces,
when performing an operation where the fastener
may contact hidden wiring. Fasteners contacting a
"live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
■
Do not switch on the product again after it has stalled.
Switching it on again, can cause a kickback with high
reaction force. Determine why the product has stalled
and rectify it, paying heed to the safety instructions. If
necessary, remove the insertion tool.
■
Ambient temperature range for tool during operation is
between 0°C and 40°C.
■
Ambient temperature range for tool storage is between
0°C and 40°C.
■
The recommended ambient temperature range for the
charging system during charging is between 10°C and
38°C.
ADDITIONAL SAFETY WARNINGS
■
Clamp workpiece with a clamping device. Unclamped
workpieces can cause severe injury and damage.
■
Injuries may be caused, or aggravated, by prolonged
use of a tool. When using any tool for prolonged periods,
ensure you take regular breaks.
■
Ambient temperature range for tool during operation is
between 0˚C and 40˚C.
■
Ambient temperature range for tool storage is between
0˚C and 40˚C.
■
The recommended ambient temperature range for the
charging system during charging is between 10˚C and
38˚C.
ADDITIONAL BATTERY SAFETY WARNINGS
■
To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse your tool,
battery pack or charger in fluid or allow fluid to flow inside
them. Corrosive or conductive fluids, such as seawater,
certain industrial chemicals, and bleach or bleach-
containing products, etc., can cause a short circuit.
■
Charge the battery pack in a location where the ambient
temperature is between 10°C and 38°C.
■
Store the battery pack in a location where the ambient
temperature is between 0°C and 40°C.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps or
tape. Do not transport batteries that are cracked or leaking.
Check with the forwarding company for further advice.
KNOW YOUR PRODUCT
See page 57.
1. Direction of rotation selector
2. Pivot locking button
3. Collet
4. LED light
5. Bit storage
6. Handle, insulated gripping surface
7. On/off switch trigger
8. Slotted bit
9. Cross slotted bit
10. LED indicator
11. Battery cap
12. USB cable
13. Battery pack
14. USB-C port
15. Operator's manual
16. USB power adaptor
MAINTENANCE
■
The product should never be connected to a power
supply when assembling parts, making adjustments,
cleaning, performing maintenance, or when the product
is not in use. Disconnecting the product from the power
supply will prevent accidental starting that could cause
serious injury.
■
When servicing, use only original manufacturer's
replacement parts, accessories and attachments. Use
of any other parts may create a hazard or cause product
damage.
■
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to various types of commercial
solvents and may be damaged by their use. Use clean
cloths to remove dirt, carbon dust, etc.
■
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
■
For greater safety and reliability, all repairs should be
performed by an authorised service centre.
SYMBOLS ON THE PRODUCT
No-load speed
V Volts
Direct current
min -1 Revolutions or reciprocations per minute
3
Original Instructions
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL