Manuels Connexes pour Beamz professional Pango 1250 Analog laser RGB
Sommaire des Matières pour Beamz professional Pango 1250 Analog laser RGB
- Page 1 Pango 1250 / 2500 Analog laser RGB Ref. nr.: 152.982 / 152.979 INSTRUCTION MANUAL GEBRUIKSAANWIJZING GEBRAUCHSANLEITUNG MANUAL DE INSTRUCCIONES MANUEL D'INSTRUCTIONS V1.3...
- Page 2 ENGLISH Congratulations to the purchase of this Beamz product. Please read this manual thoroughly prior to using the unit in order to benefit fully from all features. Read the manual prior to using the unit. Follow the instructions in order not to invalidate the warranty. Take all precautions to avoid fire and/or electrical shock.
- Page 3 NEDERLANDS Hartelijk dank voor de aanschaf van dit Beamz apparaat. Neemt U a.u.b. een paar momenten de tijd om deze handleiding zorgvuldig te lezen, aangezien wij graag willen dat u onze producten snel en volledig gebruikt. Lees deze handleiding eerst door alvorens het product te gebruiken. Volg de instructies op anders zou de garantie wel eens kunnen vervallen.
- Page 4 DEUTSCH Vielen Dank für den Kauf dieses Beamz gerat. Nehmen Sie sich einen Augenblick Zeit, um diese Anleitung sorgfältig durchzulesen, damit sie die Möglichkeiten, die unser Produkt bietet, sofort voll ausnutzen können. Lesen Sie erst die Anleitung vollständig vor der ersten Inbetriebnahme durch. Befolgen Sie die Anweisung, da sonst jeglicher Garantieanspruch verfällt. Treffen Sie stets alle Sicherheits-vorkehrungen um Feuer und/oder Stromschlag zu vermeiden.
- Page 5 ESPAÑOL Enhorabuena por la compra de este efecto de luces Beamz. Por favor lea atentamente este manual antes de usar el aparato para disfrutar al completo de sus prestaciones. Seguir las instrucciones le permite no invalidar la garantía. Tome todas las precauciones para evitar que se produzca fuego o una descarga eléctrica.
- Page 6 FRANÇAIS Nous vous remercions d’avoir acheté un appareil Beamz. Veuillez lire la présente notice avant l’utilisation afin de pouvoir en profiter pleinement. Veuillez lire la notice avant utilisation. Respectez impérativement les instructions afin de continuer à bénéficier de la garantie. Prenez toutes les précautions nécessaires pour éviter tout incendie ou décharge électrique.
- Page 7 LASERSAFETY Read for the commissioning of the laser all safety instructions and technical data of this manual carefully and thoroughly. Laser Light is different from any other light source with which you may be familiar. The light from this product can potentially cause eye injury if not set up and used properly.
- Page 8 INSTALLATION CAUTION: Please consider the respective national norms during the installation! The installation must only be carried out by an authorized employee or dealers! This fixture has been designed to be hung. It is recommended for safety purposes, your lighting effect are properly mounted using a suitable hanging clamp and safety cable.
- Page 9 FRONT AND REAR PANEL – PANGO 1250 1. Laser Aperture 2. Running LED 3. Power LED indicator 4. Mic LED 5. DMX signal LED 6. Key switch 7. Interlock 8. Sound active microphone 9. LCD function setting panel 10. X invert 11.
- Page 10 FRONT AND REAR PANEL – PANGO 2500 1. Laser Aperture 2. DMX signal LED 3. Mic LED 4. Power LED indicator 5. False LED 6. Interlock 7. Sound sensitivity knob 8. LCD function setting panel 9. 9. Y invert 10. X invert 11.
- Page 11 DISPLAY The control board offer several features: you can simple set the starting address, run the pre-programmed program or make a reset. The main menu is accessed by pressing the Mode-button, browse through the submenu by pressing Up or Down. Press the Enter-button in order to select the desired menu.
- Page 12 DMX-512 CONNECTION If you are using a standard DMX controller, you can connect the DMX output of the controller directly to the DMX input of the first unit in a DMX chain. Always connect the output of one unit with the input of the next unit until all units are connected.
- Page 13 MX CHANNELS Channel Function Value Description 000-041 Laser OFF Laser OFF 042-083 DMX mode, CH2-CH12 valid 084-125 Build in animation graphics auto running mode Auto Activate 126-167 Build in beam graphics auto running mode 168-209 Build in beam graphics auto running mode 210-251 Build in animation graphics auto running mode Sound Activate...
- Page 14 TECHNICAL SPECIFICATION Pango 1250 Pango 2500 Ref.nr: 152.982 152.979 Laser Green 200mW @532nm 400mW @532nm Laser Red 300mW @635nm 600mW @637nm Laser Blue 750mW @447nm 1500mW @447nm Guaranteed laser power 1000mW 2000mW Max. laser power 1250mW 2500mW Scanner system 30K high speed optical 40K high speed optical scanner scanner...
- Page 15 Bedrijvenpark Twente 415 7602 KM – ALMELO +31(0)546589299 +31(0)546589298 The Netherlands Product number: 152.982; 152.979 Product Description: Pango 1250 Analog laser RGB 30kpps Pango 2500 Analog laser RGB 40kpps Trade Name: BEAMZ PROFESSIONAL Regulatory Requirement: EN 60598-1:2008+A11:2009 EN 60598-2-17:1989+A2:1991 EN 55015:2013...
- Page 16 www.tronios.com Copyright © 2015 by TRONIOS the Netherlands...