Asist AE2V20A-201-BMC Mode D'emploi page 47

! Always remove the battery from the tool before
cleaning and maintenance.
Your tool requires no additional lubrication or
maintenance. There are no parts that you can repair.
Never use water or chemical cleaners to clean your
tools. Wipe it with a dry cloth.
Keep the motor fan vents clean.
Never clean any part of the tool with a hard, sharp or
rough object.
Storage when not used for a long time
Do not store the tool in a place where the temperature
is high.
If possible, store the tool in a place with a constant
temperature and humidity.
TECHNICAL SPECIFICATIONS
Working voltage 20V DC
Speed without load 1 0-400 min-1
Speed without load 2 0-1600 min-1
Quick-release chuck 13 mm
Battery: 1x 2000mAh,
Li-Ion (can also be used for other Asist-Aku Gang
machines)
Checking the state of charge of the accumulator
Charging unit Prim. 230V~50Hz, 65W
Sec. 21V, 2.3A
Maximum tightening torque 50 N.m
Charging time 1h (fast charge)
Torque setting: 19 + 1
Weight 3.75 kg
Electronic speed control
SPINDEL LOCK – chuck lock
SOFT GRIP
QUICK STOP
Led light
Sound pressure level measured according to EN
60745:
LpA (sound pressure) 70 dB dB (A) KpA=3
LWA (sound power) 80 dB (A) KwA=3
Take appropriate measures to protect your hearing!
Wear hearing protection whenever the sound
pressure exceeds the level of 80 dB (A).
Weighted effective acceleration according to EN
60745:
<2,5 m/s2 K=1.5
Caution: The vibration level may vary during
power tool operation from the declared value
depending on the way the power tool is used and
depending on the following conditions: Method of
power tool use and type of material being cut or
drilled, conditions of the power tool and method
of its maintenance, appropriateness of the used
accessories and ensuring its sharpness and good
conditions, the strength of handle gripping, use of
anti-vibration equipment, suitability of the power
tool for the purpose for which it has been designed
and compliance with workflows according to
manufacturer's instructions.
If this power tool is used in an inappropriate manner,
a hand/shoulder vibration syndrome may appear.
Caution: For clarification, it is necessary to consider
the level of vibrations in specific conditions of use in
all operating modes, e.g. the time when the power
tool is switched off except for the operation time,
and when it idles, i.e. performs no work. This may
substantially decrease the exposition level during the
whole operating cycle.
Minimize the risk of vibrations, use sharp chisels, drill
and blades.
Keepthe power toolin compliancewith
theseinstructions and provide for its proper
lubrication.
When using the power tool regularly, invest into anti-
vibration equipment.
Do not use the power tool under temperatures lower
than 10°C. Plan your project containing work with the
power tool producing high vibrations carefully and
spread it over more days.
Subject to changes.
ENVIRONMENTAL PROTECTIONWASTE
MANAGEMENT
Power tools, accessories and packaging should
be provided for recycling and not to harm the
environment.
Do not dispose of power tools into household waste!
According to Directive 2012/19/EU of the European
Parliament and of the Council on waste electrical and
electronic equipment (WEEE) and its approximation
in national laws, unfit power tools must be handed
over at the point of purchase of similar equipment, or
in available collection points designated for collection
and disposal of power tools. Such disposed power
tools will be collected, disassembled and delivered for
environment-friendly recycling.
WARRANTY
In the attached material, you will find our warranty
conditions.
Date of Manufacture
The date of manufacture is incorporated into the
serial number stated in the product nameplate.
The serial number has the format of ORD-YY- -SERI,
where ORD is the number of purchase order, YY
stands for the year of manufacture,
of manufacture and SERI means the serial product
number.
47
is the month