Publicité
Les langues disponibles
Les langues disponibles
n.............. rated speed
The "C" and "US" indicators adjacent to the
CSA Mark signify that the product has been
evaluated to the applicable CSA and ANSI/
UL Standards, for use in Canada and the U.S.,
respectively.
4. Overview
See page 2.
1 "Quick"clamping nut *
2 Spindle
3 Auobalancer support flange *
4 Spindle locking button
5 Sliding on/off switch *
6 Handle
7 Electronic signal indicator *
8 Thumbwheel for selection of speed *
9 Trigger switch *
10 Eyelet (for fall protection)*
11 Paddle switch *
12 Additional handle/Additional handle with vibration
damping *
13 Safety cover
14 Support flange
15 2-hole nut *
16 2-hole spanner *
17 Lever for safety guard attachment
* depending on equipment/not in scope of delivery
5. Commissioning
Before using the tool, check to make sure that
the rated mains voltage and mains frequency,
as stated on the rating label, correspond to your
power supply.
Always install an RCD with a maximum trip
current of 30 mA upstream.
5.1
Attaching the additional handle
Always work with the additional handle (12)
attached! Attach the additional handle on the
left or right of the machine and secure.
5.2
Attach the safety guard
For safety reasons, always use the safety
guard provided for the respective wheel! See
also chapter 10. Accessories!
Safety guard for grinding
Designed for work with roughing wheels, flap
sanding pads, diamond cut-off wheels.
See illustration D on page 2.
- Push and hold the lever (17). Place the safety
guard (13) in the position indicated.
- Release the lever and turn the safety guard until
the lever engages.
- Push the lever and turn the safety guard until the
closed section is facing the operator.
- Make sure that the guard is placed securely: The
lever must engage and you should not be able to
turn the safety guard.
(Disassemble in reverse order.)
6. Attaching the grinding disc
Prior to any conversion work: Pull the mains
plug from the socket. The machine must be
switched off and the spindle at a standstill.
For reasons of safety, attach the cutting guard
before performing cutting-off operations (see
chapter 10. Accessories).
6.1
Locking the spindle
- Press in the spindle locking button (4) and turn the
spindle (2) by hand until the spindle locking button
engages.
6.2
Placing the grinding wheel in position
WA..., WBA..., WE...A...:
See illustration A on page 2.
The Autobalancer support flange (3) is
permanently fitted on the spindle. As is the
case with most other angle grinders, a detachable
support flange is not necessary.
The contact surfaces of the Autobalancer
support flange (3), grinding wheel and the
"Quick" clamping nut (1) must be clean. Clean if
necessary.
- Place the grinding wheel on the Autobalancer
support flange (3).
The grinding wheel must lie flat on the
Autobalancer supporting flange.
WPB..., WEPB 17-..., WEPB 19-...:
See Figure B on Page 2.
- Fit the support flange (14) on the spindle. The
flange should not turn on the spindle when
properly attached.
- Place the grinding disc on the support flange (14).
The grinding disc must lay flat on the supporting
flange. The metal flange on the parting grinder
disc must lay flat on the support flange.
6.3
Securing/Releasing the "Quick"
clamping nut (depending on features)
Securing the "Quick" clamping nut (1):
Only attach the "Quick" clamping nut (1) to
tools with "Metabo Quick System". These
tools can be identified by the red spindle lock button
(4) with "M-Quick" logo
Do not use the "Quick" clamping nut if the
accessory has a clamping shank thicker than
7.1 mm! In this case, use the 2-hole nut (15) with 2-
hole spanner (16).
- Lock the spindle (see chapter 6.1).
ENGLISH en
Use only accessories that
are covered by at least
3.4 mm by the safety guard.
11
Publicité
