Télécharger Imprimer la page

MTD products 19B30031OEM Manuel De L'utilisateur page 7

Bac récupérateur double

Publicité

Les langues disponibles

Les langues disponibles

2.
Install the clevis pin (710-0309A)
from hardware pack 689-02364
into the tractor's hitch and secure
with a cotter pin (714-0117).
See Figure 8.
NOTE: The clevis pin can be fed down
through the hitch plate and secured
underneath with the cotter pin, or it may
be easier to feed the clevis pin up through
the hitch plate hole and secure with the
cotter pin on the topside. Insert the cotter
pin into the top hole, closest to the head
of the pin. You may need to push up on the pin to make the hole accessible.
IMPORTANT: If you decided to leave the hitch support only finger tight during the assembly
process, tighten all of the hardware securely at this time.
Mount the Vertical
Support Bracket
1.
Install the vertical support bracket
onto the mounting assembly on the
tractor by hooking it over the cross
mounting bracket. See Figure 9.
2.
Align the vertical support bracket
with the hole that best suits the
deck size of your tractor.
3.
Secure the bag support assembly to
the mounting assembly using a
carriage bolt (710-0276) and wing
knob (720-04122) from hardware
pack 689-02364. See Figure 10.
NOTE: Hole "A" is suggested for 38"
decks, Hole "B" is suggested for 42" decks
and Hole "C" is suggested for 46" decks.
Some kits may contain plates with the
deck size suggestions instead of letters.
Install Top Bagger Components
With the mounting brackets assembled and
in place on the tractor, follow these steps to
assemble the remaining bagger components.
1.
Snap the upper chute support (731-17091)
in place by first clipping the side portion
onto the hanger assembly rail (1), as
shown in Figure 8.
2.
Snap the front side of the upper chute
support to the rail (2), as shown in
Figure 8.
3.
If not already done so by the factory,
install the screen (731-06504) into
the bagger cover (631-04292) by first
inserting the end closest to the side with
the cut-out (1) into the mounting hole,
as in Figure 9..
ASSEMBLY & INSTALLATION
Align hole on
bracket with hole
on tractor
Figure 8
38" Deck
42" Deck
46" Deck
A B C
Figure 9
Figure 10
Figure 11
1
Figure 12
4.
Make sure to feed the screen under the
lip. Clip in the other side by pushing the
screen into the provided cut-out (2). See
Figure 10.
5.
Install the bagger cover onto the hanger
assembly, as seen in Figure 11. The cover
goes inside the two mounting tabs.
6.
Slide the hinge pin (711-04988) into
the hole located on the mounting tab,
as shown in Figure 12. Use the cut-out
window (see inset in Figure 12) to line
up the hinge pin on the other side and
push pin all the way in until it reaches the
end-stop. At this point the pin clips into
place and is secured by a tab in the bagger
cover. See Figure 13.
7.
Open bagger cover by pushing in on the
rear, right-side tab with your right hand
(1), and lifting the cover with your left
hand in the center rear of
the bagger cover (2) as shown in Figure 14.
8.
Install both grass bag assemblies (664-
05104) onto the hanger assembly rails by
inserting the front edge in first (1), and then setting the back edge down until it fits into
Figure 15
Figure 17
7
2
Make sure screen sits
under the cover's lip
Figure 13
Figure 14
the assembly (2), as shown in Figure 15.
Figure 16
1
Figure 18
2

Publicité

loading