Publicité
Les langues disponibles
Les langues disponibles
•
Do not touch the moving sanding sheet
•
Do not continue to use worn, torn or heavily clogged
sanding sheets
•
When sanding metal, sparks are generated; do not use
vacuum cleaner and keep other persons and combustible
material from work area
BATTERIES
•
The battery supplied is partially charged (to ensure
full capacity of the battery, completely charge the battery
in the battery charger before using your power tool for the
first time)
•
Only use the following batteries and chargers with
this tool
- SKIL battery: BR1*31****
- SKIL charger: CR1*31****
•
Do not use the battery when damaged; it should be
replaced
•
Do not disassemble the battery
•
Do not expose tool/battery to rain
•
Permitted ambient temperature (tool/charger/battery):
- when charging 4...40°C
- during operation –20...+50°C
- during storage –20...+50°C
EXPLANATION OF SYMBOLS ON TOOL/BATTERY
3 This tool accepts most commonly available multi-tool
accessories, including existing OIS and Starlock basic
accessories
4 Read the instruction manual before use
5 Batteries may explode when disposed of in fire, so do not
burn battery for any reason
6 Store tool/charger/battery in locations where temperature
will not exceed 50°C
7 Do not dispose of electric tools and batteries together
with household waste material
USE
•
Charging battery
! read the safety warnings and instructions
provided with the charger
•
Removing/installing the battery 2
•
Battery level indicator 8
- press the battery level indicator button M to show the
current battery level 8 a
! when the lowest level of the battery indicator
starts flashing after pressing button M 8 b, the
battery is empty
! when 2 levels of the battery indicator start flashing
after pressing button M 8 c, the battery is not
within the allowable operating temperature range
•
LED-light L 9
LED-light automatically lights on when activating the on/
off switch
! when LED-light starts flashing, the battery
protection is activated (see below)
•
Battery protection
The tool is suddenly being switched off or prevented from
being switched on, when
- the load is too high --> remove load and restart
- the battery temperature is not within the allowable
operating temperature range of -20 to +50°C --> 2
levels of the battery level indicator start flashing when
pressing button M 8 c; wait until battery has returned
within the allowable operating temperature range
- the battery is nearly empty (to protect against
deep discharge) --> a low battery level or flashing low
battery level 8 b is shown by the battery level indicator
when pressing button M; charge battery
! do not continue to press the on/off switch after the
tool is switched off automatically; battery may be
damaged
•
Changing accessories q
! remove battery from tool
- remove/mount the required accessory as illustrated
- ensure that the openings of the accessory engage into
the tabs of the tool head (any snap-in position possible)
- mount the accessory with the depressed centre
pointing downwards
- check the tight seating of the accessory (incorrect
or not securely fastened accessories can come loose
during operation and create a hazard)
•
Mounting of sanding sheet w
- tap the dust out of the VELCRO material on sanding
pad E before mounting the sanding sheet
- mount VELCRO sanding sheet H as illustrated
! replace worn sanding sheets in time
! always use the tool with the total VELCRO surface
covered with sanding paper
•
On/off
- switch on/off the tool by pushing switch C 2 in "I"/"O"
position
! before the accessory reaches the workpiece, the
tool should run at full speed
! before switching off the tool, you should lift it from
the workpiece
•
Adjusting working speed e
- with wheel D the required oscillating frequency can
be adjusted from low (1) to high (6) (also while tool is
running)
- the optimal working speed depends on the material
and can be determined with practical trials
•
Holding and guiding the tool
! while working, always hold the tool at the grey-
coloured grip area(s) r
- keep ventilation slots K uncovered
- do not apply too much pressure on the tool (excessive
pressure will cause excessive heat and may shorten
the service life of the accessory)
APPLICATION ADVICE
•
For optimal results on different materials use table
t as reference for determining the right accessory
(accessories not standard included)
•
For more information see www.skil.com
MAINTENANCE / SERVICE
•
This tool is not intended for professional use
Always keep tool clean (especially ventilation slots K 2 )
•
! remove battery from tool before cleaning
•
If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
11
Publicité
