Important Safety Instructions - Master Proheat STC PH-1600 Mode D'emploi

Important Safety Instructions

Heat guns are a source of extremely high-tem-
perature flameless heat (up to 1050˚F / 566˚C).
Extreme caution should be observed when using
these products. READ and FOLLOW these
instructions.
Use only on properly-rated electrical
circuits.
Connect to properly grounded outlets
only.
Disconnect from power source during
service and when replacing parts.
120V/15A 230V/8A
To reduce risk of fire or electric
shock, do not expose heat gun to
rain or moisture.
Store indoors.
Do not use near flammable materials
or where fumes, gases or dust are
present.
Do not use in presence of explosive
atmosphere.
Keep nozzle at least 1"/2.5 cm from
work surface.
Do not apply to the same place for a
long time.
Be aware that heat may be conducted
to combustible materials that are out
of sight.
Use in well-ventilated area.
Use caution in confined areas.
Do not leave heat gun unattended
when it is switched on.
Place heat gun on its stand after
use and allow it to cool down before
storage.
2
Caution! Laser radiation. Do not stare
into beam. Class 1 laser product.
When using an extension cord, use
only a 3-wired grounded cord rated
equal to or greater than the appliance.
Connect to properly grounded outlets
only.
120V/15A 230V/8A
Keep away from children and persons
with reduced physical, sensory or
mental capabilities or lack of experi-
ence or knowledge.
Do not direct air stream at people
or pets.
Do not drop.
Wear safety glasses at all times.
Do not touch nozzle until cool.
Recycle properly.
www.masterappliance.com
Introduction, Product Warranty, Features
& Specifications
Introduction
Master's ProHeat STC is the first heat gun of its kind that has the ability to sense and control
the temperature of the work surface. This is done by setting the desired target temperature
on the LCD and watching the actual work suface temperature increase until it reaches your
target temperature. The ProHeat 1600 is perfect for use on temperature sensitive surfaces
of all types where heat control is needed. The ProHeat 1610 Dual Mode heat gun takes heat
gun technology a step further and allows the user to toggle between surface temperature
sensing mode and the traditional nozzle control heat gun mode.
Whether you chose the PH-1600 or PH-1610, be sure to take time and familiarize yourself
with the safety and operating instructions inside this manual.
Product Warranty
Master Heat Tools are carefully tested and inspected before being shipped from the factory.
We warrant our products to be free from defects in materials and workmanship, under normal
use and service, for one year from date of purchase. In the event of a defect in materials or
workmanship we will either repair or replace, without charge at our option, any part which in
our judgement shows evidence of such defect.
Warranty does not apply to wearable items such as attachments, brushes, heating elements,
solder tips, heat tips, burners or ejectors, which require periodic replacement, nor does it
apply if the heat tool has been misused, abused, tampered with or altered.
At the end of the warranty period, Master Appliance shall be under no further obligation,
expressed or implied. Master Appliance assumes no responsibility for, and this warranty shall
not cover, any incidental or consequential damages from any defect in products or their use.
This warranty gives you specific rights. You may also have other rights which may vary from
state to state. Warranty information is included within the Instruction Manual for each product
or may be obtained by contacting Master's Customer Service Department.
Master Appliance Corp.
Attention: Repair Department
2420 18th Street
Racine, WI 53403-2381
USA
Features
Variable Variable Digital
Airflow Temp. Display
Model Name
Model No.
ProHeat STC
PH-1600 , PH-2600
ProHeat STC Dual Mode
PH-1610 , PH-2610
Specifications
Model Max Max Temperature Setting
V ac Hz
No. Watt Amp
PH-1600
120 60 1426 11
PH-1610 90 - 500˚F
40 - 270˚C
PH-2600
230 50/60 1320 6.8
PH-2610
Note:
www.masterappliance.com
262-633-7791
800-558-9413 (USA)
sales@masterappliance.com
www.masterappliance.com
Temperature Control
Lock Use At-
Controls Surface Nozzle tachments
Net Noise
Airflow
Wt. Emission
Mode
170 - 1000˚F 4-16 CFM 30 oz
<70 dB(A)
80 - 540˚C .11-.45 CMM 850 g
-models PH-1610, PH-2610 only
3