BOMANN CL 6061 CB Mode D'emploi page 42

WARNING:
• Non-rechargeable batteries are not to be recharged.
• Ensure correct polarity when inserting the battery / batteries.
CAUTION:
• When not using the remote control for a long period of time, remove
the batteries in order to prevent "leakage" of battery acid.
• Different battery types or new and used batteries must not be used
together.
• Do not dispose of batteries along with domestic waste. Return used
batteries to the relevant collection facilities or your retailer.
Unpacking the Appliance
1. Remove the appliance from its packaging.
2. Remove all the packaging material such as plastic bags, filler mate-
rial, cable ties and cardboard packaging.
3. Check that all parts are supplied in the package.
Scope of Delivery
1 Air conditioning appliance
1 Remote control
2 Batteries
1 Flexible exhaust pipe
1 Exhaust pipe adapter (Connection on the appliance)
1 Window kit, 2-piece
1 Adapter for the window exhaust kit
1 Water hose
2 Plugs (spares)
Overview of the Components
1 Control panel with display
2 Air outlet (pivoting flap)
3 Housing
4 Water outlet
5 Handle
6 Exhaust pipe connector
7 Mains cable
8 Water outlet
9 Window kit, 2-piece
10 Remote control
11 Flexible exhaust pipe
12 Adapter for the window exhaust kit
13 Exhaust pipe adapter
14 Grid on the air intake (with built-in filter insert)
Overview of Buttons, Icons and Indicator Lights
Control Panel
1 Indicator light (timer operation enabled)
2 HIGH indicator light (high fan speed)
3 LOW indicator light (low fan speed)
4 Display
5 COOL indicator light (cooling)
6 DRY indicator light (dehumidifying)
7 FAN indicator light (fan)
8 Indicator light (sleep mode)
9 POWER indicator light
10 FULL indicator light (water tank full)
11 POWER button (switch appliance on / off)
12 SLEEP button (set "sleep mode")
13 MODE button (set operating mode)
42
CL6061CB_IM
14 and buttons (adjust temperature or hour)
15 SPEED button (set fan speed)
16 TIMER button (set timer)
Remote Control
1 MODE button (set operating mode)
2 TIMER button (set timer)
3 POWER button (switch appliance on / off)
4 TEMP+ TEMP- buttons (adjust temperature or hour)
5 SLEEP button (set "sleep mode")
6 SPEED button (set fan speed)
Notes for Use
CAUTION: Important for initial operation or after transport!
Before initial operation, the appliance must stay in an upright position
for at least 3 hours in order for the cooling agent to sink. The compres-
sor will be damaged otherwise.
CAUTION:
• When you interrupt the operation with the POWER
for at least 3 minutes before switching the appliance on again.
• If you want to move the appliance to another location, first empty
the water tank!
• The appliance operates most effectively with a room size up to 70 m³.
• The flexible exhaust hose and the adapter have been manufactured
especially for this appliance. In order to avoid incorrect operation, do
not replace the pipe with another pipe.
• The exhaust pipe can be extended up to 150 cm. Do not use any
extension.
• Ensure free airflow. Make sure not to kink or bend the exhaust pipe.
Any blockage can cause the appliance to overheat.
• Close all windows and doors in order to prevent outside air from
entering the room and thus allowing a more effective operation of the
appliance.
Putting into Service
Location
• When installing the appliance, make sure to keep a distance of at
least 50 cm between the appliance and any walls or other objects.
• The surface must be flat and dry.
Assembly of Exhaust Pipe
NOTE:
For sliding windows or external roller blinds you may use the supplied
window exhaust air kit in a vertical or horizontal orientation. Adjust the
length of the seal plate as desired.
1. Connect the adapter to the exhaust hose. Place the exhaust hose in
a way that the first fin of the hose lays in the rail. Tighten the adapter
by turning it clockwise.
2. Connect the adapter to the connector on the back of the appliance. To
do this, push the adapter from the right into the guides until it stops.
3. Extend the pipe to the desired length.
4. Screw the window exhaust air kit adapter onto the end of the exhaust
air hose.
5. If the window does not have a roller shutter and is not a sliding
window, then proceed as follows:
a) Stick the open end of the pipe into a window.
b) Close the window as far as possible.
button, wait
07.11.22