Silverline 935765 Mode D'emploi page 10

GB
Product Familiarisation
1. High Pressure Hose Reel
2. Hose Reel Handle
3. Hose Connector
4. Power Cord Hook
5. ON/OFF Switch
6. Water Inlet
7. Nozzle Rest
8. Lance Bracket
9. Front Handle
10. Telescopic Rear Handle
11. Detergent Bottle
12. Wheels
13. Power Cord
14. Lance Handle Bayonet Socket
15. Lance High Pressure Hose Connector
16. Lance Handle Grip
17. Trigger
18. Trigger Lock
19. Nozzle
20. Pressure Adjustment
21. Nozzle Bayonet Connector
22. Lance Extension Bayonet Socket
23. Lance Extension Bayonet Connector
24. Cleaning Pin
25. Inlet Hose Connector
26. Rear Handle Release Button
Intended Use
Pressure washer for general, light to medium duty cleaning tasks on vehicles, buildings and other
suitable surfaces, using a jet of cold, pressurised water, with or without detergent .
Unpacking Your Tool
• Carefully unpack and inspect your product . Fully familiarise yourself with all its features and
functions
• Ensure that all parts of the product are present and in good condition . If any parts are missing or
damaged, have such parts replaced before attempting to use this product
Before Use
• Always check all parts and attachments are secure, and that hoses are not kinked or obstructed
• Always wear appropriate personal protective equipment for the job at hand . Use of this appliance
requires safety goggles and waterproof clothing
• Always use an RCD when connecting a pressure washer to the mains with a tripping current of no
more than 30mA, and a delay in operating of no more than 30ms
• Make sure mains connection points are out of reach of the pressure washer water spray and any
water that may collect on surrounding surfaces
• Only use a mains extension cable suitable for outdoor use and capable of carrying the required
current for this product . The cable must be protected against water ingress and maintain water-
tight connections where it connects to the pressure washer
10
• This product must be earthed and any extension cables used must have an earth connection
• Always use the pressure washer vertically and make sure it is used on a flat, level surface
Assembly
• Do not connect the pressure washer to the water or electrical supply until fully assembled and
ready for use
• Remove all packaging materials from the product
Hooks & holders
• Slide the Lance Bracket (8) down onto the side clip (Fig. I)
• Slide the Nozzle Rest (7) back onto the clip (Fig. II) and fix with the supplied screw
• Slide the Power Cord Hook (4) down onto the side clip (Fig. III)
Lance
• Assemble the Lance by connecting the Nozzle (19) shaft to the lance extension shaft, and these to
the lance handle (Image A)
• To do this, insert the Nozzle Bayonet Connector (21) into the Lance Extension Bayonet Socket
(22), then push and rotate to lock into place (Image B)
• Insert the Lance Extension Bayonet Connector (23) into the Lance Handle Bayonet Socket (14),
then push and rotate to lock into place (Image C)
Note: When not in use, the assembled lance can be held in the Lance Bracket (8) with the Nozzle
(19) in the Nozzle Rest (7) (Image D) .
High pressure hose
1 . Carefully pull out a length of hose from the High Pressure Hose Reel (1) (Image E)
2 . Attach the end of the hose to the Lance High Pressure Hose Connector (15) (Image F) and screw
the nut on tight
WARNING: If the high pressure hose is damaged it could burst and cause injury . A damaged hose
must be replaced, not repaired . Inspect regularly and prevent the hose from coming into contact
with sharp objects or rough surfaces . After use, always wind the hose back in using the Hose Reel
Handle (2) (Image G then H) .
Connecting to water supply
WARNING: When connecting a pressure washer to a normal domestic water supply, it is important a
non-return valve is fitted to the hose (also called backflow preventer) to ensure the pressure washer
cannot contaminate your water supply if there is a backflow.
1. Remove the plastic cap from the Water Inlet (6) (Fig. IV) and check that the filter inside is clear of
debris or other material; clean if required
2 . Fit the Inlet Hose Connector (25) (Fig . V) and tighten by hand
3 . Connect a hose from your water supply to the Inlet Hose Connector
Notes:
• The specification lists suitable water inlet pressures. A typical, normal UK household water supply
can range from 1–8bar pressure but 2–5bar is more typical . Do not exceed the maximum water
pressure stated in the specification
• If you do not know or are unable to measure the water pressure, keep the pressure low to prevent
damage to the pressure washer . Aim to set the pressure at mid-point between the lowest and
highest pressure accepted by the pressure washer . If preferred, a third party water pressure
gauge is available that connects directly to the tap . This will allow the water pressure to be set
more accurately
• Do not connect to a hot water supply . This will prevent the pump from cooling and may damage
the seals over time
• It is important that a good water connection is maintained while operating a pressure washer as
the pump will be damaged if run without water . Make sure the connections are secure before
switching on the pressure washer
Connecting to other water sources
Note: The pump featured in this pressure washer features a self-priming feature that allows use of
other water sources typically a water butt or other container of captured rain water or similar .
• Ensure the water supply is clean and filtered before entering the pressure washer. Ensure there is
no sediment
• For water butts, where the output is at the bottom, gravity will provide some pressure to assist the
pressure washer
• The hose to the water supply should not exceed 3m in length and the diameter should not be
less than 19mm or ¾"
Filling the detergent bottle
• Remove the cap on the Detergent Bottle (11) and fill with a pressure washer-compatible
detergent if required (Image I)
• The pressure washer is designed to dispense detergent on the low pressure setting, and dispense
clear liquid on the high pressure setting
• The detergent ratio is variable depending on the pressure adjuster setting