Publicité
Les langues disponibles
Les langues disponibles
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of
the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to the
trigger time.
Labels on tool
:
The following pictograms are shown on the tool:
Warning! To reduce the risk of injury, the user must
read the instruction manual.
Electrical safety
#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Gel comfort grip
3. Dust extraction outlet
4. Sanding disc
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting sanding sheets (fig. A)
Warning! Never use the tool without a sanding sheet or
accessory in place.
Press the sheet firmly and evenly onto the sanding disc (4),
u
making sure that the holes in the sheet line up with the
holes in the base.
Fitting and removing the dustbag (fig. B)
Fit the dustbag (5) into the dust extraction outlet (3).
u
To remove the dustbag, pull it off the dust extraction outlet.
u
Connecting a vacuum cleaner (fig. C)
Insert the adaptor (6) into the dust extraction outlet (3).
u
Connect the hose (7) of the vacuum cleaner to the adaptor.
u
Use
Warning! Let the tool work at its own pace. Do not overload.
Switching on and off
To switch the tool on, set the on/off switch (1) to position I.
u
To switch the tool off, set the on/off switch to position O.
u
Emptying the dustbag
The dustbag should be emptied every 10 minutes.
Shake the dustbag to empty the contents.
u
Hints for optimum use (fig. D - G)
Do not exert too much pressure on the tool.
u
Regularly check the condition of the sanding sheet.
u
Replace when necessary.
Always sand with the grain of the wood.
u
When sanding new layers of paint before applying another
u
layer, use extra fine grit.
On very uneven surfaces, or when removing layers of
u
paint, start with a coarse grit. On other surfaces, start with
a medium grit. In both cases, gradually change to a fine
grit for a smooth finish.
Consult your retailer for more information on available
u
accessories.
Accessories
The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to
high quality standards and designed to enhance the
performance of your tool. By using these accessories you will
get the very best from your tool.
Maintenance
Your Black & Decker corded/cordless appliance/tool has been
designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
u
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
u
switch off.
Unplug the charger before cleaning it. Your charger does
u
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your appliance/tool/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
u
Do not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
u
from the interior (when fitted).
ENGLISH
7
Publicité
