Publicité
Les langues disponibles
Les langues disponibles
OUTSIDE BACK EXHAUST
B
INSTALLATION OVERVIEW
B1. Prepare Rear Wall
B2. Remove Blower Plate
B3. Attach Mounting Plate to Wall
B4. Prepare Top Cabinet
B5. Adjust Blower
B6. Mount the Microwave Oven
IMPORTANT NOTES:
•
Make sure the screws for the
blower motor and blower plate
are securely tightened when
they are reinstalled. This will
help to prevent excessive
vibration.
•
Make sure the motor wiring has
been properly routed and secured,
and that the wires are not pinched.
PREPARING THE REAR WALL
B1.
FOR OUTSIDE BACK EXHAUST
You need to cut an opening in the rear wall for
outside exhaust.
NOT E:
IT IS VERY
READ
AND FOLL
IMPO RTAN
IN THE
INST ALLA
OW THE
T TO
BEFO
DIRE CTIO
RE PRO
TION INST
NS
REAR
WAL L
CEED
ING WITH
RUC TION
This Rear
TEM PLAT
THIS
S
Wall Templa
E.
3/8" TO EDGE
mounti
ng plate
te serves
outlet.
and to
locate the
to positio
12"
1. Use
a level
horizon
n the bottom
accura
to check
tal exhaus
2. Locate
tely.
that the
templa
t
and mark
te is positio
right side
of the centerl
at least
one stud
ned
ine.
on the
4"
screw mounte
I t is importa
nt to use
left or
of the microw
d firmly
at least
locatio ns
ave. Mark
in a stud
to suppor
one wood
for the
two additio
t the weight
3. Drill
holes in
supplie
d toggle
nal, evenly
a stud,
the marked
bolts.
spaced
that do
drill a 3/16"
hole for
locatio ns.
toggle
not line
up with
wood screws
Where
there is
bolts.
a stud,
. For holes
D O NOT
drill 5/8"
holes for
AT THIS
TIME.
INSTA LL
4. Remov
THE MOUN
5. Review
e the templa
TING PLATE
installa
the Installa
te from
the rear
tion situatio
tion Instruc
wall.
n.
tion book
for your
Darle vuelta
versió n
en Españ
a la hoja
para consu
ol.
ltar la
Loca te
and mark
moun ting
holes to
plate .
align with
IMPO RTAN
holes in
LOCA
T:
the
TE AT
THE CEN
LEAS T
TERL INE.
ONE STUD
MAR K
ON EITH
THE LOCA
ER SIDE
SPAC
ED TOG
TION FOR
OF
AREA
GLE BOLT
2 ADD
.
S IN THE
ITION AL,
EVEN
MOU NTIN
LY
G PLAT
E
Trim the
rear wall
temp late
along
the dotte
d line.
Loca te
and mark
moun ting
holes to
plate .
IMPO RTAN
T:
LOCA
TE AT
LEAS T
THE CEN
MAR K
TERL INE.
THE LOCA
SPAC
ED TOG
AREA
GLE BOLT
.
•
Read the instructions on the REAR
WALL TEMPLATE.
•
Tape it to the rear wall.
•
Cut the opening, following the instructions of the
REAR WALL TEMPLATE.
Installation Instructions
NOTE: IT IS VERY IMPORTANT
TO
READ AND FOLLOW
THE DIRECTIONS
N INSTRUCTION S
IN THE INSTALLATIO
WITH THIS
BEFORE PROCEEDING
REAR WALL TEMPLATE.
serves to position the bottom
This Rear Wall Template
the horizontal exhaust
mounting plate and to locate
outlet.
that the template is positioned
1. Use a level to check
accurately.
2. Locate and mark at least
one stud on the left or
right side of the centerline.
It is important to use at
least one wood
a stud to support the weight
screw mounted firmly in
two additional, evenly spaced
of the microwave. Mark
locations for the supplied
toggle bolts.
locations. Where there is
3. Drill holes in the marked
for wood screws. For holes
a stud, drill a 3/16" hole
that do not line up with a
stud, drill 5/8" holes for
toggle bolts.
DO NOT INSTALL THE
MOUNTING PLATE
AT THIS TIME.
4. Remove the template
from the rear wall.
Instruction book for your
5. Review the Installation
installation situation.
para consultar la
Darle vuelta a la hoja
versión en Español.
to align with holes in the
Locate and mark holes
mounting plate.
IMPORTANT:
STUD ON EITHER SIDE
LOCATE AT LEAST ONE
THE CENTERLINE .
EVENLY
FOR 2 ADDITIONAL,
MARK THE LOCATION
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
AREA.
along the dotted line.
Trim the rear wall template
Trim the
rear wall
temp late
along
the dotte
d line.
align with
holes in
the
ONE STUD
ON EITH
ER SIDE
TION FOR
OF
2 ADD
ITION AL,
S IN THE
EVEN
MOU NTIN
LY
G PLAT
E
(Horizontal Duct)
3/8" TO EDGE
along the dotted line.
Trim the rear wall template
12"
4"
OF
to align with holes in the
Locate and mark holes
mounting plate.
IMPORTANT:
STUD ON EITHER SIDE
OF
LOCATE AT LEAST ONE
THE CENTERLINE .
EVENLY
MARK THE LOCATION
FOR 2 ADDITIONAL,
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
AREA.
IMPORTANT :Do not remove the cardboard
spacers between the heat shield and door.
REMOVE BLOWER PLATE
B2.
Remove and save the screw that holds the blower
plate to the microwave. Lift off the blower plate.
Blower Plate
EN-16
Back of
Microwave
Publicité
