Publicité
Les langues disponibles
Les langues disponibles
INSTALLATION INSTRUCTIONS
STEP 1. SPOUT ROUGH-IN & SPOUT INSTALLATION
a) Install the spout rough-in box taking into account the minimum spout air gap* dimension shown
in Fig. 5.
b) The 90° elbow requires bracing, i.e. copper strapping.
c) The 90° elbow is adjustable for up to 1" (25 mm) thick backsplashes from finished wall.
d) The aerator has a swivel head that can be adjusted up to 7° for fine tuning of the water stream.
e) Connect water supply, flush system, then install aerator.
STEP 2. SENSOR ROUGH-IN AND CONTROLLER/SENSOR INSTALLATION
a) Install the 4x4 rough-in boxes flush to -1/4" (-6 mm) to the finished wall.
STEP 3. CONTROLLER & SENSOR PLATE INSTALLATION
a) Install the controller/converter assembly inside the 4x4x4 rough-in
box by removing the adhesive backings from the hook and loop pads
on the back of the controller and sticking them to the inside of the box.
Note: The rough-in should be installed flush to the finished wall to -1/4"
(-6 mm) recessed. Refer to Fig. 5. Note: False activations may be
triggered by highly reflective surfaces such as mirrors or stainless steel
partitions. Contact Technical Service for assistance/troubleshooting.
b) Take the solenoid wires from controller and route them out of the box
through the wire bushing and then to the solenoid. Refer to Figs. 6
and 8. Connect the red solenoid wire to "+" marked solenoid terminal
on valve, black wire to the other terminal. Solenoid extension wires
are available (060680A).
c) Install a CSA and/or UL approved "Class 2" transformer or equivalent
(purchased separately) in a convenient location (do not install inside
the rough-in box). With the power supply off, bring the 24 VAC supply
wires into the rough-in box through the wire bushing. Connect the
wires to the hardwire converter. Coil up any excess wire. Repeat for
second sensor plate assembly.
d) Once both controllers are properly wired, turn "ON" the power supply
for the transformer. Connect the sensor to the controller. Take the
excess wire and wrap neatly inside the box, ensuring the wires will not
be pinched when installing cover plates.
e) The controller is factory set to 8" (203 mm) sensor range and a 10
second duration. Refer to Fig. 8.
f) Install the sensor plates onto the rough-in box using the driver bit and
screw kits provided. To ensure proper sealing, the plates must be
installed flush to the finished wall. The finished wall surface should be
smooth, flat and free of obstructions. It is recommended to install the
mixed (red ring) plate on the left hand side. Refer to Fig. 7.
97mm
(3.8")
061201A
Sensor Box Rough-In
(4x4 box, plaster guard,
wire bushing)
Fig. 6
104mm
(4.1")
104mm
(4.1")
Wire Bushing
w w w . s p e c s e l e c t . c o m
102mm
(4")
Backsplash
0 to 1"
Rough-In
0 to -1/4"
57mm (2.25") Min.
19mm
(3/4")
Max.
Sill Depth**
Recommended***
* A minimum 57mm (2-1/4") installation height above fixture rim is required
unless a greater air gap is designated by local codes/regulations.
** A maximum sill depth of 19mm (3/4") from backsplash to sink edge is allowable.
*** It is recommended that a sink with a dimension shown in Fig. 5 be used.
76mm-76mm
(3.0"-3.0")
56mm
(2.2")
155mm
(6.1")
Slip on spout tube
(must be braced,
i.e. copper strapping)
063220A
Slip on Spout Box Rough-In
(4x2 box, plaster guard,
tube bushing, 90° elbow)
Page 2
Fig. 4
TYPICAL INSTALLATION
O-ring
Nut
063218A
Slip on Spout
O-ring (12 pcs)
063219A
Spout Kit
(spout, nut, slip on O-ring
& mounting O-ring)
90° Elbow
(is adjustable for up to 1" (25 mm)
thick backsplashes from finished wall)
Slip on Spout Tube
(must be braced, i.e. copper strapping)
*
Recommended***
140mm
(5.5")
104mm
(4.1")
22.5° Spout to be
oriented as shown
Note: Aerator has
swivel head with 7°
of rotational movement
061178A
1.5 GPM Laminar Flow
Insert Swivel Head
152mm
(6")
Fig. 5
208626 Rev. A
Publicité
