Laica HYDROSMART+ METAL STOP GENOVA Instructions Et Garantie page 7

EN GENOVA tap filter
6) To install the connector with the M adapter, proceed as follows:
Remove the fastening ring from the connector and take the L adapter with Ø21 mm diameter, then assemble the
-
three pieces as described in figure 6A, 6B and 6C.
6A
N
- Loosen the fastening band with a flat head screwdriver and remove the smaller seal inside the adapter M (fig.
7A, 7B).
7A
- Choose the best seal: only the one with the largest diameter (fig. 8A) or both with one inserted inside the other,
pressing firmly and taking extra care over the direction in which they are inserted (fig. 8B).
8A 8B
- Install the adapter M on the tap and tighten the fastening band using a flat
head screwdriver to secure it firmly to the tap (fig. 9A and B).
9A 9B
7) Remove the HYDROSMART™ METAL STOP filter from its packaging and rinse it under running water. Now hook
the filter to the connector as shown in figure 11A, 11B, 11C.
11A 11B
6B 6C
N
7B
- Screw the connector onto
the ring (fig. 10).
10
11C
12
Instructions and guarantee
SMART FILTRATION SYSTEM – FREE LAICA HOME
WELLNESS APP - USE
List of compatible devices:
• iOS: iPhone with version 10 operating system.
• For devices with Android™ operating system:
from version 6.0 (Marshmallow).
By adding the HYDROSMART™ METAL STOP filter to
the free "Laica Home Wellness" app, you can receive
automatic notification on your smartphone when to
replace the filter.
1. Install the free "Laica Home Wellness" app on your
smartphone.
2. Start the app and enter the "FILTER" section from the
main screen.
3. Add the HYDROSMART™ METAL STOP FILTER by
pressing the "+" key. It is possible to add the filter by
scanning the QR code printed on the upper part of the
filter or manually by pressing the "Select manually"
button.4. The app adds the filter and automatically
prompts the replacement date.
To optimise the effective duration of the filter based
on the water treated, you can select the chlorine level
in your water supply.
To use it properly, request further information from your
water supplier or carry out a preliminary assessment
of the local water supply.
5. Save the settings by pressing the " " key.
6. When the filter replacement date is reached,
the notification to replace it will appear on your
smartphone. The notification is also sent to the email
address given during registration.
• To scan the QR code on the upper part of the
filter, you must authorise the app to access
to your smartphone camera.
• To receive notifications when to replace the
filter, you must enable the settings on your
smartphone.
• To replace the filter, you can add a new one
by scanning the QR code printed on the
upper part of the filter or by updating the
expiry date by clicking on the "Filter expired"
button (click to replace)".
USING THE FILTERING SYSTEM
Activating the GENOVA HYDROSMART™ METAL
STOP filter:
When first used and every time the HYDROSMART™
METAL STOP filter is changed, turn the tap on and allow
the water to flow through the filter for several minutes (at
least 4-5 minutes) to correctly activate the materials of
which the filter is composed. This water can be used for
watering plants. If the GENOVA filtering system has not
been used for 24 hours or more, allow the water to flow
for 30-60 seconds before using the filtered water again.
CAUTION:
- To guarantee the performance characteristics of the
filtering system, it is recommended to filter cold water
only.
- The flow of water at a temperature higher than 50°C
through the connector may cause permanent damage.
The flow of water at a temperature higher than 35°C
through the filter may cause permanent damage.
- To adjust the water flow properly, open the tap slowly.
The GENOVA filtering system has 2 different ways of
dispensing the water which can be selected with the
selector C:
1) Filtered water for
drinking, washing
fruit and vegetables,
cooking and carry out
all routine tasks with
safe, pleasant tasting
water.
2) Unfiltered water with
spray head.
REPLACING THE FILTER
To replace the filter, turn the filter anticlockwise and
remove it by pulling it outwards (fig. 12A, 12B, 12C).
12A 12B
12C
Replace it with a new filter repeating the steps described
in point 7 of the paragraph "PREPARING THE FILTERING
SYSTEM" and "USING THE FILTERING SYSTEM - Activating
the HYDROSMART™ METAL STOP filter".
To achieve the best results and guarantee the safety of the
filtering system, we recommend replacing the filter every
4 months or 1200 litres of filtered water.
CARE AND MAINTENANCE
Ensure your hands are clean during maintenance
operations on the filtering system. Regularly clean the
external part of the filter with a damp sponge and rinse
with cold running drinkable water.
Regularly clean the outer part of the connector with
a damp sponge and delicate detergent, then rinse
thoroughly with cold drinking water.
Do not use aggressive detergents, solvents, chemical or
abrasive products.
It is recommended to thoroughly clean the entire
connector each time the filter is changed.
For maintenance, remove the entire filtering system by
following the installation instructions in reverse order.
1) Rinse the connector under unfiltered running drinking
water.
Do not use detergents, solvents, chemical or abrasive
products to clean the connector.
If necessary, remove the fastening ring (E), the rubber
13
EN