ADEO SCREEN XTR3 Manuel D'installation Et D'utilisation page 13

Fixed frame screen with masking installation and operation manual
The type of motor installed on the product is identified by a label applied on each product showing the CE logo. When unwrapping the product please check the model type indicated on the label in order to
perform the installation and cable connections correctly. Should the power of the motor be different from that of the supply network of the installation place, please contact an electrician to have a current and
Hz transformer installed.
ELECTRICAL CONNECTION: electric cabling must be conformant with applicable IEC standards. IEC norm EN 60335-1 requires that supply network be fitted with an omnipolar
selector switch with contact opening distance of at least 3 mm.
For each motor (e.g. plug switch etc.). In case of need, this device ensures that the power supply is safely and quickly cut off.
Use the wires as described in the figure.
ATTENTION:
The number of motors depends on the product type and more importantly on the number of maskings (e.g. XTR3 – 2 maskings). Screens are provided with cabling and switches to
manage fabric movement and with plugs to connect to the mains power supply.
Bus cables (white-orange/white/white-black) must be isolated if not used for the interface.
WARNING:
Correctly performed, state-of-the-art, norm-compliant electrical connections are important to prevent accidents and to ensure the screen's optimal and unaltered performance over
time. Prior to carrying out any operation on electrical parts ensure that power supply is disconnected.
Operates with standard radio control (supplied).
Technical characteristics <=130"
Nice RF 230V 50Hz:
Frequency: ~Hz50
Power: 120W
Torque: 8Nm
Speed: 17Rpm
Max no. of cycles: 2
Cable length: 2.5 mt
Mechanical strength: EN14202 conformant
Operating T°:
from –20 to +55 °C
Frequency: 433.92 MHz
Trans. range: 150mt
Weighted sound pressure level: LpA ≤ 70 dB(A)
Motor protection class: IP44
Made by Adeo Screen Sp. Z o.o. (Poland) Specifications are subject to change without notice. E&OE
Please verify that you are working with the latest revision of this document before specifying your screen.
Doc: XTR3 – Installation Manual rev3 | 27.10.2020
09 MOTOR TYPE IDENTIFICATION –CHARACTERISTICS – ELECTRICAL CONNECTION
Technical characteristics >130"
Nice RF 230V 50Hz:
Frequency: ~Hz50
Power: 170W
Torque: 15Nm
Speed: 17Rpm
Max no. of cycles: 2
Cable length: 2.5 mt
Mechanical strength: EN14202 conformant
Operating T°:
from –20 to +55 °C
Frequency: 433.92 MHz
Trans. range: 150mt
Weighted sound pressure level: LpA ≤ 70 dB(A)
Motor protection class: IP44
Technical characteristics <=130"
Nice RF 120V 60Hz:
Frequency: ~Hz60
Power: 190W
Torque: 133 in. lb
Speed: 20rpm
Max no. of cycles: 2
Cable length: 2.5 mt
Mechanical strength: EN14202 conformant
Operating T°:
from –20 to +55 °C
Frequency: 433.92 MHz
Trans. range: 150mt
Weighted sound pressure level: LpA ≤ 70 dB(A)
Motor protection class: IP44
ENGLISH
Do not connect, to isolate
SB (13) - White– to isolate if interface not present
GB (14) - White-black– to isolate if interface not present
Not provided in standard option
Technical characteristics >130"
Nice RF 120V 60Hz:
Frequency: ~Hz60
Power: 190W
Torque: 133 in. lb
Speed: 20rpm
Max no. of cycles: 2
Cable length: 2.5 mt
Mechanical strength: EN14202 conformant
Operating T°:
from –20 to +55 °C
Frequency: 433.92 MHz
Trans. range: 150mt
Weighted sound pressure level: LpA ≤ 70 dB(A)
Motor protection class: IP44
Page 13