Indesit SBM 18 V Serie Mode D'emploi page 19

Installation
! Before placing your new appliance into operation please read
these operating instructions carefully. They contain important
information for safe use, for installation and for care of the appliance.
! Please keep these operating instructions for future reference. Pass
them on to possible new owners of the appliance.
Positioning and connection
Positioning
1. Place the appliance in a well-ventilated humidity-free room.
2. Do not obstruct the rear fan grills. The compressor and
condenser give off heat and require good ventilation to operate
correctly and save energy.
3. Leave a space of at least 10 cm between the top part of the
appliance and any furniture above it, and at least 5 cm between
the sides and any furniture/side walls.
4. Ensure the appliance is away from any sources of heat (direct
sunlight, electric stove, etc.).
5. In order to maintain the correct distance between the appliance
and the wall behind it, fit the spacers supplied in the installation
kit, following the instructions provided.
Levelling
1. Install the appliance on a level and rigid floor.
2. If the floor is not perfectly horizontal, adjust the refrigerator by
tightening or loosening the front feet.
Electrical connections
After the appliance has been transported, carefully place it vertically
and wait at least 3 hours before connecting it to the electricity
mains. Before inserting the plug into the electrical socket ensure the
following:
• The appliance is earthed and the plug is compliant with the law.
• The socket can withstand the maximum power of the appliance,
which is indicated on the data plate located on the bottom left
side of the fridge (e.g. 150 W).
• The voltage must be in the range between the values indicated
on the data plate located on the bottom left side (e.g. 220-240V).
• The socket is compatible with the plug of the appliance. If
the socket is incompatible with the plug, ask an authorised
technician to replace it (see Assistance). Do not use extension
cords or multiple sockets.
! Once the appliance has been installed, the power supply cable
and the electrical socket must be easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by authorised
technicians only (see Assistance).
! The manufacturer declines any liability should these safety
measures not be observed.
Accessories
*
SHELVES : with or without grill.
Due to the special guides the shelves are removable and
the height is adjustable (see diagram), allowing easy storage
of large containers and food. Height can be adjusted without
complete removal of the shelf.
*
TEMPERATURE Indicator light: to identify the coldest area in
the refrigerator.
1. Check that OK appears clearly on the indicator light (see
diagram).
2. If the word "OK" does not appear it means that the
temperature is too high: adjust the REFRIGERATOR
OPERATION knob to a higher (colder) position and wait
approximately 10 hours until the temperature has stabilised.
3. Check the indicator light again: if necessary, readjust it
following the initial process. If large quantities of food have
been added or if the refrigerator door has been opened
frequently, it is normal for the indicator not to show OK.
Wait at least 10 hours before adjusting the REFRIGERATOR
OPERATION knob to a higher setting.
Start-up and use
Starting the appliance
! Before starting the appliance, follow the installation
instructions (see Installation).
! Before connecting the appliance, clean the compartments
and accessories well with lukewarm water and bicarbonate.
1. Insert the plug into the socket and ensure that the internal
light illuminates.
2. Turn the TEMPERATURE ADJUSTMENT knob to an average
value. After a few hours you will be able to put food in the
refrigerator.
Setting the temperature
The temperature inside the refrigerator compartment
automatically adjusts itself according to the position of the
thermostat knob.
1
= warmest
MAX = coldest
We recommend, however, a medium position.
The cooling section of the refrigerator is located inside the
back wall of the refrigerator compartment for increased space
and improved aesthetics. During operation, the back wall will
be covered in frost or water droplets depending on whether
the compressor is operating or paused. Do not worry, the
refrigerator is functioning normally.
Chiller system
The appliance comes with one of the chiller systems described
below: take note of your system in order to determine the most
efficient food storage method.
PURE WIND *
It is recognizable due to the presence of the mechanism on the
top part of the refrigerator compartment (see diagram).
*
Varies by number and/or position, available only on certain
models.
GB
19